Automatic anti-dazzle rear-view mirror 9-3 CV 2

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

1. Saab 9-3 CV M04- 9-5 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 CV M04- Automatic anti-dazzle rear-view mirror Accessories Part No. Group Date Instruction Part No. Replaces 12 833 884 12 833 886 9:85-24 Apr 03 12 833 885 F980A250

2. 2 12 833 885 Saab 9-3 CV M04- 1 Remove and disconnect the roof lighting. 2 Remove the mirror base cover panel. 3 Remove the rear-view mirror. 4 Plug in the connector. 5 Run the wiring harness to the left of the rear- view mirror mounting and fit the rear-view mirror. 6 Fit the mirror base cover panel. 7 Connect and fit the roof lighting. 8 Check the function of the mirror and the lamps. 9 Rear-view mirror with compass: Calibrate the compass, see page 3. If necessary, change compass zone, see page 3. 10 Hand over the installation instructions to the customer and bring attention to the user instructions. WARNING Make sure the wiring harness is not pinched. Incorrect fitting can damage the cables and cause short-circuits/fire. F980A251 1,7 2,6 3,5 3,5 1,7 1,7 4

3. 12 833 885 3 Saab 9-3 CV M04- User instructions The rear-view mirror has two sensors, one facing the front and the other facing the rear. When the front-facing sensor detects that it is dark outside, the system will be activated so that any bright light fall- ing from behind will gradually darken the rear-view mirror to reduce the brightness. As the bright light subsides, the mirror will gradually return to normal. Automatic anti-dazzle can be switched off using the button under the rear-view mirror. For other ques- tions, refer to the Owner's Manual. Calibration/Programming Rear-view mirror with compass: Calibrate the compass by holding the “AUTO” button depressed until “CAL” and a compass point are shown in the compass window. Release the button. Slowly drive the car in a circle until “CAL” disappears. The com- pass is now calibrated. For other questions, refer to the Owner's Manual. Rear-view mirror with compass: Change the com- pass zone by holding the “AUTO” button depressed until “ZONE” and a compass point are shown in the compass window. Release the button. You can now change the compass zone using the “AUTO” button (see illustration for compass zone options). Release the “AUTO” button once the correct compass zone has been selected. Once “ZONE” disappears, the compass zone is stored. For other questions, refer to the Owner's Manual. Rear-view mirror with garage door remote control: For programming, see the Owner's Manual. D980A352 3 3 4 4 5 5 6 6 7 7 8 8 9 9 1 2 10 10 11 11 12 12 13 13 14 15

Weergaven

  • 624 Totale weergaven
  • 512 Websiteweergaven
  • 112 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 22 www.saabpartners.com
  • 10 saabpartners.com
  • 3 52.29.207.161
  • 2 54.154.214.138