Branch cable set LHD 900, 9000, 9-3, 9-5

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

13. 86 95 926 13 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 A Branch connector set BTimer set E930A133 B A

2. 2 86 95 926 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 1 Branch connector 2 220 V socket 3 Connecting cable 4 Connecting cable 5 Grommet 6Screw (2) 7 Cable tie (10) 8Screw E930A128 2 4 3 6 5 1 8 7

8. 8 86 95 926 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 15 Pull the connecting cable forward through the seal at the removable bulkhead partition and along the right-hand structural member to the expansion tank above the right-hand wheel hou- sing. Follow the A/C pipes, if fitted. 16 Lubricate the intake cable O-ring and connect the cable to the branch connector (A). If the car is already equipped with an engine heater, the cable should first be detached from it. 17 Connect the 2-metre connecting cable from the cabin socket to the branch connector (B) and the 1-metre connecting cable to the branch con- nector (C). 18 Connect the 1.5-metre connecting cable from the branch connector (C) to the engine heater and fit the lock brace over the connection to the engine heater. A click will be heard when the clip is correctly fitted in place. 19 Position the branch connector on the wheel hou- sing, mark the position of the hole using the con- nector as a template and drill the hole with a 3.5 mm bit. 20 Deburr the hole and remove loose swarf and fla- kes of paint. Clean with Teroson FL cleaner. Apply Standox 1K Füllprimer. Apply finish paint. Use Terotex HV400 or Mercasol 1 on inside sur- faces. 21 Fit the branch connector. 22 Make sure that no cables in the engine bay are in contact with hot or sharp components. Secure the cables as necessary. 23 Connect the equipment to a 220 V mains supply and check the 220 V socket with a voltmeter. 24 Fit the cover over the bulkhead partition space. 25 Fit the upper section of the dashboard, speaker grilles and A pillasr trim. Do not forget the screw that is accessible when the glove box lid is open or, if the car is equipped with a passenger air- bag, that is behind the SRS emblem. C930A029 21 17C 17B 16A

11. 86 95 926 11 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 11 Lay the 2.0 m extension cable along the heater hoses to the bulkhead partition. From the bulk- head, the extension cable is to follow the wiring harness to the right. 12 Fit the kit’s grommet on the connecting cable. E930A132 11 11

7. 86 95 926 7 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 9 Position the cabin socket next to the front brack- et for the centre console side panel, mark the positions of the holes using the socket as a template and drill the holes with a 3 mm bit. 10 Remove the side panel and introduce the con- necting cable. 11 Refit the centre console’s side panel. 12 Connect the 2-metre connecting cable to the cabin socket and screw the socket in place. 13 Fold the carpet back into place and refit the clip. 14 Refit the right-hand noise baffle under the dash- board. 10 12 C930A028

12. 12 86 95 926 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 13 Insert the 2.0 m extension cable through the bulkhead grommet to where the cabin outlet is to be fitted. Secure the cable with cable ties. Timer cables, if any, should be inserted at the same time. 14 Fit the grommet from the set from the outside and seal it with Terosan T 242 (part no. 30 15 781) or equivalent sealant. 15 Place the mains outlet on the knee protection panel close to the A-pillar, see illustration. Mark the position of the holes with an awl. 16 Connect the 2.0 m extension cable to the mains outlet and screw on the outlet. 17 Automatic cars: Reconnect the control module cable lug. 18 Refit the coolant hose on cooled glove box. Refit the glove box. 19 Refit the left-hand direction indicator. 20 Make sure there are no cables in the engine bay that are in contact with hot or sharp details. Secure the cables on non-moving parts with cable ties. 21 Connect to the mains and check the mains out- let with a voltmeter. 22 Refit the battery and connect it. Adjust the car clock and date, and program the radio code if the radio is not a Saab original. 18 17 15 18 18 E930A131

10. 10 86 95 926 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 8 Remove the glove box and fold away the top of the carpet. If the glove box is cooled, detach the coolant hose. On automatic cars: Undo the cable lug from the control module and put the cable out of the way. 9 Measure out and drill a 22 mm hole with a hole saw, see illustration. Cut away a small piece of the insulation on the outside of the bulkhead partition. 10 Remove burrs, loose cuttings and paint flakes from the hole. Clean with Teroson Cleaner FL. Apply Standox 1K Füllprimer and finishing paint. Use Terotex HV 400 or Mecasol 1 on inner sur- faces. 8 9 8 110mm 60mm 8 8 E930A130

5. 86 95 926 5 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 12 Remove the grille, right-hand direction indicator and headlamp. 13 Remove the air cleaner and put it to one side. 14 Lubricate the intake cable O-ring and connect the cable to the branch connector (A). If the car is already fitted with an engine block heater: Unplug the cable from the engine heater. Withdraw the intake cable and push it up between the radiator and bumper member. Rou- te the cable below the right-hand headlamp and further to the branch connector. Lubricate the intake cable O-ring and connect the cable to the branch connector (A). 15 Connect the 2.0 m extension cable to branch connector (B) and the 1.5 m extension cable to branch connector (C). 16 Connect the 1.5 m extension cable from branch connector C to the engine heater and fit the lock brace and heat shield. 17 Position the branch connector correctly on the wing liner below the right-hand direction indica- tor. Mark the hole and drill it using a 3.5 mm bit. 18 Deburr the hole and remove loose swarf and fla- kes of paint. Clean with Teroson FL cleaner. Apply Standox 1K Füllprimer. Apply finish paint. Use Terotex HV400 or Mercasol 1 on inside sur- faces. 19 Mount the branch connector. Spray thin corrosi- on inhibitor, part no. 30 15 971, on the grounding point when the cable lug has been mounted. 20 Make sure there are no cables in the engine bay that are in contact with hot or sharp details. Secure the cables if necessary. 21 Connect to a mains outlet and check with a volt- meter. 22 Refit the right-hand headlamp, direction indica- tor, air cleaner and grille. D930A141 19 17 14A 15C 15B

3. 86 95 926 3 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 Saab 900 M94-M98, Saab 9-3 1 With cruise control (B204/B234): Dismantle the cruise control module by unplugging the connector and undoing the nuts. Lift away the control module. 2 Remove tape and fastenings at the bulkhead grommet. 3 Remove the glove box and the air duct to the right-hand side air vent and fold back the insula- ting mat. WARNING It is essential that the extension cable O-rings are lubricated before fitting and that all connections are pressed home properly. 3 3 2 1 D930A075

6. 6 86 95 926 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 Saab 9000 1 Remove the cover over the bulkhead partition space. 2 Remove the noise baffle below the dashboard on the passenger side. 3 Fold the carpet aside, remove the clip securing the insulating mat and carefully bend it down. 4 Remove the trim from both A pillars, both spea- ker grilles and the screw that becomes acces- sible when the glove box lid is opened, or behind the SRS emblem if the car is equipped with a passenger airbag (use a magnetic screwdriver), and lift up the upper section of the dashboard. 5 From the bulkhead partition space in the engine bay, drill a 22 mm hole in the bulkhead partition in the area between the evaporator casing (cars with A/C or ACC) or the fresh-air filter (cars wit- hout A/C). Use a hole saw. 6 Deburr the hole and remove loose swarf and fla- kes of paint. Clean with Teroson FL cleaner. Apply Standox 1K Füllprimer. Apply finish paint. Use Terotex HV400 or Mercasol 1 on inside sur- faces. 7 Insert the 2-metre connecting cable through the bulkhead partition to the place where the cabin socket is to be mounted. Timer cables, if any, should be inserted at the same time. 8 Fit the kit’s grommet from the inside and seal it with Terosan T242 (part no. 30 15 781) or equi- valent sealant so that water cannot run down the cable into the cabin. WARNING It is essential that O-rings are lubricated before fit- ting and that all connections are pressed home properly. 7 C930A027

1. Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 900 Monteringsanvisning SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTALLATIONS DE MONTAGE SITdefault Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 Branch cable set LHD Accessories Part No. Group Date Instruction Part No. Replaces 400 127 866 9:87-24 May 00 86 95 926 86 95 926 Feb 00 E930A142

4. 4 86 95 926 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 4 Pull the 2.0 m extension cable through the bulk- head. Timer cables, if any, should be pulled through at the same time. 5 Connect the 2-metre connecting cable to the cabin socket and position the socket close to the right-hand A pillar. 6 Run the connecting cable inside the bulkhead partition and fasten it to the car’s wiring harness, see illustration, so that it is not close to sharp edges or the like. Secure it in front of the glove box. 7 Seal the grommet with Teroson T242 (part no. 30 15 781) or equivalent sealant to prevent water running down the cable into the cabin. 8 Fit a cable tie around the grommet and seal with adhesive tape. 9 Refit the air duct and glove box. If necessary, measure and cut out the glove box for a better fit against the connector cable. 10 Mount the cabin socket below the dashboard near the A pillar, see illustration. Use an awl to mark the position of the hole. Screw the socket in place. 11 With cruise control (B204/B234): Fit the cruise control module. Note Use soap solution to make it easier. D930A140 4 10 6

9. 86 95 926 9 Saab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5 Saab 9-5 1 If the car is fitted with a radio that is not a Saab original radio, make sure the customer is in pos- session of the radio code before commencing. Disconnect and lift out the battery. 2 Remove the left-hand direction indicator. 3 If the car is already fitted with an engine heater, its cable must first be disconnected. 4 Plug in the connector to the branch connector (A). Mark the position of the holes using the con- nector as a template, see illustration. Use a 5.5 mm drill and drill the holes. 5 Deburr the hole and remove loose swarf and fla- kes of paint. Clean with Teroson FL cleaner. Apply Standox 1K Füllprimer. Apply finish paint. Use Terotex HV400 or Mercasol 1 on inside sur- faces. 6 Connect the 2.0 m extension cable to the branch connector (B) and the 1.5 m extension cable to the branch connector (C). Screw on the branch connector. 7 Connect the 1.5 m extension cable from the branch connector (C) to the engine heater and fit the lock brace. Roll up the excess cable from the insert heater to the branch connector and fasten it beside the battery tray. WARNING It is essential that the extension cable O-rings are lubricated before fitting and that all connections are pressed home properly. Important Use a drill stop to avoid drilling into the washer flu- id reservoir. 7 3,7 3 6 90mm E930A129 6B 6C 4A

Weergaven

  • 624 Totale weergaven
  • 510 Websiteweergaven
  • 114 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 5 saabpartners.com
  • 16 www.saabpartners.com
  • 2 52.29.207.161
  • 4 54.154.214.138