Installations instructions Adapter harness, mobile phone 9-3, 9-5

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

3. 32 025 908 3 9-3 M03-06, radio/navigation 9-3 M03-06, radio/navigation 1 Move the passenger seat to its rearmost posi- tion. 2 Disconnect the battery negative cable (-). 3 Remove the front floor console side piece on the passenger side. 4 Remove the ashtray/storage compartment.

4. 4 32 025 908 9-3 M03-06, radio/navigation 5 Remove the ACC/MCC unit. 6 Unplug the connectors. 7 Remove the head unit, press in the catches and take the unit out. 8 Unplug the head unit connectors.

8. 8 32 025 908 9-3 M03-06, radio/navigation 18 Fit the ACC/MCC unit. 19 Fit the floor console's front side protection. 20 Connect the battery negative cable (-).

11. 32 025 908 11 9-3 M07-, radio 9-3 M07-, radio 1 Move the passenger seat to its rearmost posi- tion. 2 Disconnect the battery negative cable (-). 3 Remove the front floor console side piece on the passenger side. 4 Remove the ashtray/storage compartment.

28. 28 32 025 908 9-5 M06-, radio/navigation 3.2 Unplug the navigation unit's connectors. 3.3 Remove the compartment. 4 Remove the ACC unit. 5 Unplug the ACC unit connectors.

35. 32 025 908 35 9-5 M06-, radio/navigation 19 Calibrate the ACC system: 19.1Start the engine. Press in the AUTO and REC buttons until the message "ACC: CALIBR. STARTED" is shown in the main instrument unit's display. Calibration takes approx. 20 seconds.

5. 32 025 908 5 9-3 M03-06, radio/navigation 9 Prepare adapter harness (32 025 898): 9.1 Cut the yellow (YE) cable to the same length as the other cables in the adapter harness. 9.2 Cut the sheathing to approx. 50 mm and strip the cable end. 9.3 Crimp the cable terminals (12 769 780) to the black/white (BK/WH), grey/white (GY/ WH) and yellow (YE) cable ends on the adapter harness. 10 Fit the adapter harness to the passenger side. Important It is very important that the correct recess in the pliers is used. Check that the cable terminal is firmly secured.

6. 6 32 025 908 9-3 M03-06, radio/navigation 11 Connect the adapter harness to the car: BK/WH -> K8B pos 9 (line gnd) GY/WH -> K8B pos 10 (line out) YE -> K8B pos 11 (mute) 12 Cut approx. 50 mm from the tape to the connec- tor K8B. 13 Splicing the wiring harness. 14 Connect the adapter harness to the car using joining sleeves: 14.1RD/BU -> 12 V socket BK (+15) Important In order to avoid damaging the wiring harness when splicing, the joining sleeve must only be clamped in once.

7. 32 025 908 7 9-3 M03-06, radio/navigation 14.2BK -> K8B pos 12 (gnd) RD -> K8B pos 16 (+30) 15 Protect the joints by insulating with fabric tape around the wiring harness. Secure the wiring harness. 16 Fit the ashtray/storage compartment. 17 Plug in the connectors. Important Secure the wiring harness firmly so that there is no risk of rattling.

13. 32 025 908 13 9-3 M07-, radio 8.2 Cut the sheathing to approx. 50 mm and strip the cable end. 8.3 Crimp the cable terminals (12 769 135) to the black/white (BK/WH), grey/white (GY/ WH) and yellow (YE) cable ends on the adapter harness. 9 Connector, overview. 10 Connect the adapter harness to the car: 10.1BK/WH -> K14 pos 5 (line gnd) 10.2GY/WH -> K14 pos 4 (line out) 10.3YE -> K16 pos 4 (mute) Important It is very important that the correct recess in the pliers is used. Check that the cable terminal is firmly secured.

14. 14 32 025 908 9-3 M07-, radio 11 Release the wiring by cutting the tape approx. 50 mm from the connectors. 12 Splicing the wiring harness. 13 Connect the adapter harness to the car using joining sleeves: 13.1BK -> K14 pos 8 (gnd) 13.2RD -> K14 pos 1 (+30) 13.3RD/BU -> 12 V socket VT/BU (+15) Important In order to avoid damaging the wiring harness when splicing, the joining sleeve must only be clamped in once.

21. 32 025 908 21 9-3 M07-, navigation 13 Plug in the voltage converter (12 769 716) to the adapter harness. 14 Connect the adapter harness to the car: 14.1GY/WH -> K16 pos 7 (line out) 14.2BK/WH -> K16 pos 15 (line gnd) 15 Splicing the wiring harness. 16 Connect the adapter harness to the car using joining sleeves: RD -> K14 pos 1 (+30) BK -> K14 pos 8 (gnd) RD/BU -> 12 V socket BU/VT (+15) Important In order to avoid damaging the wiring harness when splicing, the joining sleeve must only be clamped in once.

22. 22 32 025 908 9-3 M07-, navigation 17 Fit the adapter harness connector adjacent to the centre console support to the passenger side. Protect the joints by insulating with fabric tape around the wiring harness and secure the wiring harnesses. 18 Fold up the catch (A), cut the cable tie (B) and remove the BCM plug. 19 Unplug the connector from the plug, prize apart and pull out. 20 Connect the yellow (YE) cable from the adapter harness to the BCM K78 (grey connector) pos 36 (mute). Important Secure the wiring harness firmly so that there is no risk of rattling.

32. 32 32 025 908 9-5 M06-, radio/navigation 11 Protect the joints by insulating with fabric tape around the wiring harness. 12 Secure the wiring and any excess. 13 Fit the ashtray/storage compartment. 14 Plug in the connectors and fit the ACC unit. Important Secure the wiring harness firmly so that there is no risk of rattling.

9. 32 025 908 9 9-3 M03-06, radio/navigation 21 Set the date and time: 21.1Turn the ignition key to the ON position (A). 21.2Press the CUSTOMIZE button (B) in the SIDC (control panel, SID). 21.3Turn the INFO button (C) until the display shows “Clock / Alarm”. Press to confirm "OK". 21.4Turn the INFO button (C) to “Set Clock”. Press "OK". 21.5Turn the INFO button (C) to “Manual” or "RDS adjust" and set the correct time. Press "OK". 21.6Turn the INFO button (C) to "DATE". 21.7Press in the INFO button (D) until the display shows "YEAR 2000". 21.8Turn the INFO button (C) to the correct year. Press to confirm "OK". 21.9Turn the INFO button (C) to the correct month. Press "OK". 21.10Turn the INFO button (C) to the correct day. Press "OK". F930A564 A B C D

12. 12 32 025 908 9-3 M07-, radio 5 Remove the ACC unit. 6 Remove the centre air vent in the dashboard by carefully bending in the hooks (A) accessible through the grille. 7 Remove the retaining screws (A), lift out the radio unit (B), unplug the connectors (C) and disconnect the antenna cable (D). 8 Prepare adapter harness (32 025 898): 8.1 Cut the yellow (YE) cable to the same length as the other cables in the adapter harness. Important Take care to bend the correct hooks (A). Hooks holding together the air vents are also visible behind the grille. Important Exercise caution when the connector locking catch is detached to avoid damaging the connec- tor. Pull the connector straight out when it is unplugged, to avoid bending the pins.

15. 32 025 908 15 9-3 M07-, radio 14 Fit the adapter harness connector adjacent to the centre console support to the passenger side and secure. 15 Protect the joints by insulating with fabric tape around the wiring harness. Secure the wiring harness. 16 Plug in the radio head unit connectors (C+D), fit the radio unit (B), and fit the retaining screws (A). 17 Fit the air vent. Important Secure the wiring harness firmly so that there is no risk of rattling. Important Secure the wiring harness firmly so that there is no risk of rattling.

19. 32 025 908 19 9-3 M07-, navigation 5 RHD: Remove the sound insulation panel (A) and the floor lighting (B) on the passenger side. 6 Remove the storage compartment/ashtray using a screwdriver. 7 Remove the ACC unit. 8 Remove the centre air vent in the dashboard by carefully bending in the hooks (A) accessible through the grille. Important Take care to bend the correct hooks (A). Hooks holding together the air vents are also visible behind the grille.

20. 20 32 025 908 9-3 M07-, navigation 9 Remove the retaining screws (A), lift out the navigation unit (B), unplug the connectors (C) and disconnect the antenna cable (D). 10 Crimp the cable terminals (32 000 135) to the black/white (BK/WH), grey/white (GY/WH) and yellow (YE) cable ends on the adapter harness. 11 Cut several centimetres of the tape approx. 90 mm (3.5 in) from the connector on the adapter harness. Cut the grey/white (GY/WH) and black/white (BK/WH) cable approx. 90 mm (3.5 in) from the connector. 12 Plug in the connector (12 789 432) to the adapter harness: 12.1Crimp the cable terminals (32 000 375) on the cable ends. 12.2Connect: GY/WH -> 1 (to the connector) BK/WH -> 2 (to the connector) GY/WH -> 3 BK/WH -> 4. Important Exercise caution when the connector locking catch is detached to avoid damaging the connec- tor. Pull the connector straight out when it is unplugged, to avoid bending the pins. Important It is very important that the correct recess in the pliers is used. Check that the cable terminal is firmly secured.

24. 24 32 025 908 9-3 M07-, navigation 25 Fit the ACC unit (A) and the storage compart- ment/ashtray (B). 26 Fit the air vent. 27 LHD: Plug in the floor lighting connector (C), fit the sound insulation panel (B) and the data link connector (A). 28 RHD: Plug in the floor lighting connector (B) and fit the sound insulation panel (A).

25. 32 025 908 25 9-3 M07-, navigation 29 Fit the floor console's side piece. 30 Connect the battery negative cable (-) 31 Set the time: 31.1Ignition in ON position. 31.2Switch on the audio system (A). 31.3Press MENU (B) until the tab for the clock is activated. 31.4Select RDS time or manual setting on the touch screen (C). To obtain RDS time (Clock Time, CT), the reception must be good and the currently tuned station must be transmit- ting RDS time signals. 32 Synchronise the remote control code by insert- ing the key into the ignition switch. Note This unit has a touch-panel and only displays time. The navigation system receives the correct date via a GPS signal. The date is used by other car functions, e.g. service, and is not shown in the display. Important Repeat this procedure with all keys. Otherwise, the remote controls will not function.

29. 32 025 908 29 9-5 M06-, radio/navigation 6 Remove the ashtray/storage compartment. 7 Prepare adapter harness: 7.1 Cut the yellow (YE) cable to the same length as other cables in the adapter harness (A). Cut the sheathing approx. 5 cm and strip the cable end. 7.2 Connect the cable terminals (12 805 740) to the yellow (YE), black/white (BK/WH) and grey/white (GY/WH) cable ends on the adapter harness. 8 Cars with radio: Connect the adapter harness to the car: 8.1 Connect with cable terminals: Yellow (YE) -> K16 pos 4 (mute) Grey/white (GY/WH) -> K14 pos 4 (line out) Black/white (GY/WH) -> K14 pos 5 (line ground) Important Check that the cable terminal is firmly secured.

30. 30 32 025 908 9-5 M06-, radio/navigation 8.2 Splicing the wiring harness. 8.3 Connect the adapter harness with joining sleeves: Red (RD) -> K14 pos 1 (+30) Black (BK) -> K14 pos 8 (ground) Red/blue (RD/BU) -> 12 V socket brown (BN) (+15) 9 Cars with navigation: Connect the adapter harness to the car: 9.1 Connect with cable terminals: Black/white (BK/WH) -> K16C pos 7 (line ground) Grey/white (GY/WH) -> K14 pos 4 (line out) Yellow (YE) -> K16C pos 16 (mute) Important In order to avoid damaging the wiring harness when splicing, the joining sleeve must only be clamped in once.

31. 32 025 908 31 9-5 M06-, radio/navigation 9.2 Splicing the wiring harness. 9.3 Connect the adapter harness with joining sleeves: Red (RD) -> K16A pos 16 (+30) Black (BK) -> K16B pos 10 (ground) Red/blue (RD/BU) -> 12 V socket brown (BN) (+15) 10 Secure the adapter harness connector with a cable tie. Important In order to avoid damaging the wiring harness when splicing, the joining sleeve must only be clamped in once. Important Secure the wiring harness firmly so that there is no risk of rattling.

33. 32 025 908 33 9-5 M06-, radio/navigation 15 Cars with radio: 15.1Plug in the radio unit's connectors, connect the antenna connection and insert the unit. 15.2Fit the screws (B) and the plugs (A). 16 Cars with navigation: 16.1Fit the compartment. 16.2Plug in the navigation unit's connectors, connect the antenna connection and insert the unit.

1. 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault 9-3 M03-06, radio/navigation . . . . . . . . . . . . . . . . . . . . . . . page 3 9-3 M07-, radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11 9-3 M07-, navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18 9-5 M06-, radio/navigation . . . . . . . . . . . . . . . . . . . . . . . . page 27 Adapter harness, mobile phone Accessories Part No. Group Date Instruction Part No. Replaces 32 025 900 9:89-32 Jan 07 32 025 908 32 025 908 Nov 06 F930A623

16. 16 32 025 908 9-3 M07-, radio 18 Fit the ACC unit (A) and the storage compart- ment/ashtray (B). 19 Fit the floor console's front side protection. 20 Connect the battery negative cable (-). 21 Set the time and date on the audio system's head unit: Manual setting of audio system without CD changer: - Press the clock button. - Press the menu button directly underneath the menu option you wish to change. - Press the menu button again to increase time or date one increment at a time. You can also adjust time and date by pressing the SEEK, FWD or REV buttons. Manual setting of audio system with CD changer: - Press the MENU button. - Press the menu button directly underneath the clock symbol in the display. - Press the menu button directly underneath the menu option you wish to change. - Press the menu button again to increase time or date one increment at a time. You can also adjust time and date by pressing the SEEK, FWD or REV buttons. Automatic setting - RDS time: To obtain RDS time (Clock Time, CT), the reception must be good and the currently tuned station must be transmitting RDS time signals. - In the clock menu, press the menu button directly underneath the arrow symbol in the display. - Press the menu button directly underneath RDS time menu option. - Adjusting the clock now takes place automatically and the display shows: "Adjusting to RDS time...". In the event of poor RDS reception or if there is no time information the display shows: No RDS time availa- ble.

18. 18 32 025 908 9-3 M07-, navigation 9-3 M07-, navigation 1 Move the passenger seat to its rearmost posi- tion. LHD: Move the driver's seat to its rearmost posi- tion. 2 Disconnect the battery negative cable (-). 3 Remove the front floor console side piece on the passenger side. LHD: Remove the front floor console side piece on the driver's side. 4 LHD: Remove the data link connector (A), the sound insulation panel (B) and unplug the floor lighting connector (C) on the driver's side.

23. 32 025 908 23 9-3 M07-, navigation 21 Plug in the connectors to the plug, connect the plug (A) and secure with cable ties (B). 22 Secure the adapter harness with cable ties. 23 Fit the adapter harness to the centre console to the passenger side. Secure with cable tie (A) and the clip (B). 24 Plug in the radio head unit connectors (C+D), fit the navigation unit (B), and fit the retaining screws (A). Important Secure the wiring harness firmly so that there is no risk of rattling. Important Secure the wiring harness firmly so that there is no risk of rattling. Important Secure the wiring harness firmly so that there is no risk of rattling.

27. 32 025 908 27 9-5 M06-, radio/navigation 9-5 M06-, radio/navigation 1 Disconnect the battery negative cable (-) 2 Cars with radio: 2.1 Remove the plugs (A) and the screws (B). 2.2 Lift out the radio and unplug the connectors and disconnect the antenna connection. 3 Cars with navigation: 3.1 Press in the special tools until they engage. Pull out the navigation unit using the tool handles. Important Remove the plugs by affixing tape for example onto each plug and then pulling it out.

26. 26 32 025 908 9-3 M07-, navigation 33 Cars with Anti-Pinch - Learn Anti-Pinch: 33.1Close the window. CV: Close the door and the soft top. 33.2Reset the pinch protection by removing and fitting fuse F5 from the instrument panel electrical centre (IPEC). The pinch protec- tion for both door modules is now reset and both front windows can be programmed. 33.3Start the car. 33.4Lower the window fully. Hold the button depressed during the entire operation. 33.5Raise the window fully. Hold the button up during the entire operation. Wait for at least 1 second when the window is in the top posi- tion. 33.6Lower the window fully. Hold the button depressed during the entire operation. 33.7Raise the window fully. Hold the button up during the entire operation. Wait for at least 1 second when the window is in the top posi- tion. 33.8When calibration has been completed an audible confirmation is heard. In the event that no audible confirmation is heard, repeat the procedure. WARNING Anti-Pinch is not active until the power windows have been calibrated following power disconnec- tion. Note Only one control module is to be calibrated at a time due to voltage variations.

10. 10 32 025 908 9-3 M03-06, radio/navigation 22 Synchronise the remote control code by insert- ing the key into the ignition switch. 23 Cars with Anti-Pinch - Learn Anti-Pinch: 23.1Close the window. CV: Close the door and the soft top. 23.2Reset the pinch protection by removing and fitting fuse F5 from the instrument panel electrical centre (IPEC). The pinch protec- tion for both door modules is now reset and both front windows can be programmed. 23.3Start the car. 23.4Lower the window fully. Hold the button depressed during the entire operation. 23.5Raise the window fully. Hold the button up during the entire operation. Wait for at least 1 second when the window is in the top posi- tion. 23.6Lower the window fully. Hold the button depressed during the entire operation. 23.7Raise the window fully. Hold the button up during the entire operation. Wait for at least 1 second when the window is in the top posi- tion. 23.8When calibration has been completed an audible confirmation is heard. In the event that no audible confirmation is heard, repeat the procedure. Important Alert the customer to the fact that all remote con- trols must be synchronised by inserting the key(s) into the ignition switch. If this is not done then the remote control will not work. WARNING Anti-Pinch is not active until the power windows have been calibrated following power disconnec- tion. Note Only one control module is to be calibrated at a time due to voltage variations.

17. 32 025 908 17 9-3 M07-, radio 22 Synchronise the remote control code by insert- ing the key into the ignition switch. 23 Cars with Anti-Pinch - Learn Anti-Pinch: 23.1Close the window. CV: Close the door and the soft top. 23.2Reset the pinch protection by removing and fitting fuse F5 from the instrument panel electrical centre (IPEC). The pinch protec- tion for both door modules is now reset and both front windows can be programmed. 23.3Start the car. 23.4Lower the window fully. Hold the button depressed during the entire operation. 23.5Raise the window fully. Hold the button up during the entire operation. Wait for at least 1 second when the window is in the top posi- tion. 23.6Lower the window fully. Hold the button depressed during the entire operation. 23.7Raise the window fully. Hold the button up during the entire operation. Wait for at least 1 second when the window is in the top posi- tion. 23.8When calibration has been completed an audible confirmation is heard. In the event that no audible confirmation is heard, repeat the procedure. Important Repeat this procedure with all keys. Otherwise, the remote controls will not function. WARNING Anti-Pinch is not active until the power windows have been calibrated following power disconnec- tion. Note Only one control module is to be calibrated at a time due to voltage variations.

34. 34 32 025 908 9-5 M06-, radio/navigation 17 Connect the battery negative cable (-). 18 Set the time and date on the audio/navigation system's head unit: Manual setting of audio system without CD changer: - Press the clock button. - Press the menu button directly underneath the menu option you wish to change. - Press the menu button again to increase time or date one increment at a time. You can also adjust time and date by pressing the SEEK, FWD or REV buttons. Manual setting of audio system with CD changer: - Press the MENU button. - Press the menu button directly underneath the clock symbol in the display. - Press the menu button directly underneath the menu option you wish to change. - Press the menu button again to increase time or date one increment at a time. You can also adjust time and date by pressing the SEEK, FWD or REV buttons. Automatic setting - RDS time: To obtain RDS time (Clock Time, CT), the reception must be good and the currently tuned station must be transmitting RDS time signals. - In the clock menu, press the menu button directly underneath the arrow symbol in the display. - Press the menu button directly underneath RDS time menu option. - Adjusting the clock now takes place automatically and the display shows: "Adjusting to RDS time...". In the event of poor RDS reception or if there is no time information the display shows: No RDS time availa- ble. Audio system with navigation: Normally the navigation system receives the correct time and date via GPS signals. - Press the button indicating time at the top right of the screen to display today's date for 5 seconds. Manual setting: If the GPS time is incorrect or if there is no GPS sig- nal then the time and date can be adjusted manu- ally. - Hold the button indicating time, at the top right of the screen, depressed for more than 2 seconds to switch to the menu for setting time. - Adjust the time and date. Important If the battery is disconnected or has been discon- nected, time will not be displayed until the audio system has received GPS signals from a satellite. The clock cannot be set manually either.

2. 2 32 025 908 9-3 M07 with navigation The following are not included in the kit but are ordered separately: · Voltage converter · Connector · Lock · Cable terminals F930A540 x1 x7 x3 x3 x3 x3 x3

Weergaven

  • 553 Totale weergaven
  • 457 Websiteweergaven
  • 96 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 5

  • 20 www.saabpartners.com
  • 3 52.29.207.161
  • 6 saabpartners.com
  • 3 52.29.207.161:8069
  • 4 54.154.214.138