Integrated telephone 9-3 CV

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

7. 12 832 515 7 Saab 9-3 CV M04- 22 Carefully remove the speaker grille from the left- hand rear side trim. Use removal tool 82 93 474. 23 Remove the screws which hold the rear side trim on the left-hand side. 24 Lift the side trim upwards. Retain any rubber protection. 25 Unhook the control module from the side trim, but do not remove the control module connector as this means a diagnostic trouble code being generated. 26 Remove the speaker connector and remove the side trim. 27 Remove the left-hand bass speaker or the left- hand cover. F930A306 22 23 23 24 26 25 27 27 27 27

8. 8 12 832 515 Saab 9-3 CV M04- 28 Remove the left-hand scuff plate. 29 Remove the lower section of the A-pillar trim on the left-hand side. F930A307 29 28

12. 12 12 832 515 Saab 9-3 CV M04- 40 Remove the connector from the amplifier. 41 Remove the small connector from the large connector. 42 Remove the fibre optic cable connected to posi- tion 1 by opening the connector locking clip and carefully lifting the hook. F930A311 41 42 42 40

14. 14 12 832 515 Saab 9-3 CV M04- 48 Remove the bracket and move it away to facili- tate access. Remove the wiring harness cable tie from the bracket. 49 Take the fibre optic cable, Luggage compartment bracket - Torsion compartment, from the kit, remove the protective cover from one connection and fit the connection in position 2 in the connec- tor inside the torsion compartment. Fit the lock. 50 Guide the fibre optic cable along the wiring harness to the left, out through the torsion com- partment, and backwards to the bracket at the REC. Secure with cable ties, but do not tighten them fully as two further cables will be secured. Continue with step 51. F930A313 49 50 48 48 49

15. 12 832 515 15 Saab 9-3 CV M04- 51 From the rear seat, guide in the kit's wiring harness with fibre optic cable in the torsion com- partment. Fit the small connector with fibre optic cables in the connector and fit the lock tab. 52 Fit the connector to the wiring harness inside the torsion compartment. Guide the kit's wiring harness along the existing wiring harness and backwards to the REC. Secure them with cable ties inside the torsion compartment. 53 Locate the connector for the telematics unit in the centre of the torsion compartment and fit the cables from the kit's wiring harness in the connector in accordance with the following: Red (RD) cable (+) in position 10 Black (BK) cable (-) in position 20 Fit the connector for the telematics unit in the large connector in the kit's wiring harness. F930A314 51 51 52 BK RD 53

16. 16 12 832 515 Saab 9-3 CV M04- 54 Guide the loose ends of the kit's wiring harness along the existing wiring harness through the previously fitted cable ties along the fibre optic cable already fitted, backwards to the wiring harness branching to the REC. Tighten the cable ties. 55 Remove the tape which is securing the connector for the telematics unit power supply at the wiring harness and unplug the connector. 56 Remove the lock and fit the cables from the kit's wiring harness in the connector in accordance with the following: Red (RD) cable (+) in position 1 Black (BK) cable (-) in position 2 57 Fit the lock, plug in the connector and secure it at the wiring harness to the REC. F930A315 54 RD 55 BK 56 56

5. 12 832 515 5 Saab 9-3 CV M04- 7 Fold down the soft top completely, but allow the soft top cover to remain open. 8 Open the rear side window on the left-hand side completely. 9 Remove the screws which hold the rear seat cushion at the front edge. 10 Lift up the cushion and pull it forwards so that it loosens. 11 Pull up both of the rear head restraints to the highest position. 12 Press in the lock on the head restraints' sleeves. Hold the lock pressed in and remove the head restraints. 13 Remove the screws for the seat belts' lower mounting. 14 Remove the two screws for the backrest cushion upper mounting. 15 Pull the backrest cushion lower section forwards and lift the backrest cushion upwards. 16 Press out the seat belt guide from the backrest cushion and move the seat belt out from the guide and the backrest cushion. 17 Lift out the backrest cushion. F930A304 10 10 12 12 9 9 13 14 15 16 16

13. 12 832 515 13 Saab 9-3 CV M04- 43 Take the fibre optic cable, Amplifier - Torsion compartment, from the kit, remove the protective cover from one connection and fit the connection in position 1 in the amplifier's small connector. Fit the lock. 44 Fit the protective cover onto the removed fibre optic cable connection and carefully move the fibre optic cable aside in order to prevent damage. 45 Fit the small connector in the large connector and connect the large connector to the amplifier. 46 Guide the fibre optic cable back along the wiring harness and into the torsion compartment. 47 Remove the protective cover from the fibre optic cable's other connection and fit the connection in position 2 in the connector inside the torsion compartment. Fit the lock. Continue with step 51. F930A312 45 43 43 45 47 47

25. 12 832 515 25 Saab 9-3 CV M04- 82 Connect the connector to the kit's control panel. 83 Fit the control panel. 84 Position and fit the air vent. F930A324 82 84 83 83

1. Saab 9-3 CV M04- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 CV M04- Integrated telephone Accessories Part No. Group Date Instruction Part No. Replaces 12 832 505 9:39-13 Nov 03 12 832 515 F930A301

6. 6 12 832 515 Saab 9-3 CV M04- 18 Locate the violet antenna cable connection at the seat belt lower mounting on the right-hand side of the car. Remove the connectors. 19 Remove the right-hand bass speaker or the right-hand cover. 20 Cut off the cable tie in order to be able to change the location of the antenna cable and fit a new cable tie in the same place, but only around the wiring harness. 21 Guide the antenna cable into the torsion compartment and position the antenna cable connection, together with the blue antenna cable connection if fitted, at the centre of the torsion compartment. Without navigation: Continue with step 22. With navigation: Continue with step 61. F930A305 20 21 21 21 19 19 19 19 18

11. 12 832 515 11 Saab 9-3 CV M04- 38 Fit the second connection to the fibre optic cable which was fitted in step 31 in position 1 in the kit's connector. 39 Cars where the bracket at the REC is fitted: Continue with step 48. Cars where there is no bracket at the REC: Continue with step 40. F930A310 38 38

22. 22 12 832 515 Saab 9-3 CV M04- 74 Fit the left-hand side trim, connect the luggage compartment lighting and hook the strap on. Fit the clips. 75 Fit the side scuff plate. 76 Fit the front section of the luggage compartment trim, the scuff plate and fit the carpet to the luggage compartment floor. Without navigation: Continue with step 77. With navigation: Continue with step 85. F930A321 75 74 74 74 76 76 74 76 76 4 76 76

23. 12 832 515 23 Saab 9-3 CV M04- 77 Fit the A-pillar trim. 78 Fit the scuff plate. Cars where the infotainment control panel has no screen: Continue with step 79. Cars where the infotainment control panel has a screen: Continue with step 85. F930A322 77 78

24. 24 12 832 515 Saab 9-3 CV M04- 79 Remove the centre air vent in the dashboard by carefully bending in the hooks accessible through the grille. 80 Remove the retaining screws for the infotainment control panel. 81 Remove the control panel and remove the connector. Note Take care to bend the correct hooks. Hooks hold- ing together the air outlet are also visible behind the grille. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A323 80 80 81 79

20. 20 12 832 515 Saab 9-3 CV M04- 69 Amplifier and/or CD changer fitted: Remove the protective cover from the second connection on the fibre optic cable previously fitted (from the torsion compartment). Fit the connection in position 1 in the small connector. Fit the lock. Fit the protective cover on the removed fibre optic cable. 70 Amplifier and/or CD changer fitted: Fit the small connector in the amplifier and the CD changer connector. 71 Amplifier and/or CD changer fitted: Plug in the amplifier and CD-changer connector. Continue with step 72. F930A319 69 69 70 69 69 70

28. 28 12 832 515 Saab 9-3 CV M04- 99 Connect the battery negative cable if not already done and fit the battery cover. 100Synchronise remote control code by inserting the key into the ignition. 101Adjust the time and date. 102Activate window lift pinch protection function by operating the side windows up and down twice. An audible confirmation will sound when activation is complete. 103 Cars where the left-hand front seat is electri- cally adjustable: Reset the position of the seat if it has been changed. 104Connect the diagnostic tool, carry out an SPS-programming of the control module, ICM (to latest software), then select “Add/Remove”, select ICM and select “Add”. 105Connect the diagnostic tool, select car and model year, select "All", select "Add/Remove", select the accessory and select "Add". Important Repeat this procedure with all keys. Otherwise, the remote controls will not function. Note The diagnostic tool will on some occasions need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display. Note The diagnostic tool will on some occasions need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display.

19. 12 832 515 19 Saab 9-3 CV M04- 67 Cars where there is no bracket at the REC: Continue with step 74. Bracket with amplifier or CD changer is fitted at the REC: Remove the amplifier or CD changer connector and remove the small connector from the large connector. Bracket with amplifier or CD changer is fitted at the REC: Remove the CD changer connector and remove the small connector from the large connector. 68 Amplifier and/or CD changer is fitted: Remove the fibre optic cable connected to position 1 in the removed connector by opening the connector locking clip and carefully lifting the hook. Care- fully guide the fibre optic cable away so that it is not damaged. F930A318 67 68 68

2. 2 12 832 515 Saab 9-3 CV M04- 1 Fibre optic cable, A-pillar - Torsion compartment, 2770 mm long 2 Fibre optic cable (x3) – Amplifier - Torsion compartment (870 mm long) – Luggage compartment console - Torsion compartment (1195 mm long) – Between the units in the luggage compart- ment console (455 mm long) 3 Wiring harness with fibre optic cable 4 Optical cable connector, 2-pin 5 Bracket for telematics unit 6 Screw (x2) 7 Antenna, Bluetooth 8 Cable tie (x17) In addition, the following items are required (ordered separately)  Telematics unit  Control panel (certain cars)  Antenna cable (certain models)  Steering wheel (certain cars) F930A302 4 1 6 5 3 2 7 8

9. 12 832 515 9 Saab 9-3 CV M04- 30 Position the left-hand front seat in its most forward position and fold the backrest forwards. 31 Take the fibre optic cable, A-pillar - Torsion compartment, from the kit and guide it from the connector at the left-hand lower A-pillar via the wiring harness by the scuff plate, under the rear seat and to the left-hand roll-bar in the torsion compartment. Secure the fibre optic cable with cable ties. 32 Raise the soft top completely and open the boot lid. Note The seat must be pushed to the rear position in order to access the whole route. Following which, push the seat back to the forward position. Important Handle the fibre optic cables with care or the signal may be distorted.  Do not bend the cable in a radius smaller than 25 mm.  The cables must not be exposed to knocks which cause the transparent plastic to whiten, which means that the light intensity is weak- ened. Such damage can cause an interruption to communication.  The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A308 31 31 31

21. 12 832 515 21 Saab 9-3 CV M04- 72 Fit the bracket. Also tighten the nut on the topside of the bracket. Secure the wiring harness cable tie in the hole in the bracket. 73 Position the bracket for the telematics unit in the torsion compartment and fit it. Important Handle the fibre optic cables with care or the signal may be distorted.  It is very important that the two cables in the connector are not mixed up.  Do not bend the cable in a radius smaller than 25 mm.  Keep the cable ends free from dirt and grime.  The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A320 72 72 72 72 72 73 73

4. 4 12 832 515 Saab 9-3 CV M04- 1 Raise the soft top and open the boot lid. 2 Remove the carpet on the luggage compartment floor and remove the luggage compartment scuff plate. 3 Remove the rivets and lift out the front section of the luggage compartment trim. 4 Remove the side scuff plate on the left-hand side. 5 Remove the clips for the left-hand side trim and fold the trim aside. Unhook the strap on the rear side of the side trim and remove the connector from the luggage compartment lighting. Remove the side trim. 6 Check from the luggage compartment if there is a connection for the antenna cable in the centre of the torsion compartment and if a telematics unit is fitted in the centre of the torsion compart- ment. If a telematics unit is fitted then it must be removed together with the bracket but without the connectors being removed. No telematics unit and no antenna connec- tion: Continue with step 7. Telematics unit and blue antenna cable connection fitted but no violet antenna cable connection: Continue with step 7. No telematics unit, and blue antenna cable connection fitted, but no violet antenna cable connection: Continue with step 7. No telematics unit but violet antenna cable connection fitted: Continue with step 22. Telematics unit and blue antenna cable connection fitted and connected, and violet antenna cable connection is fitted but not connected: Continue with step 61. No telematics unit, but blue antenna cable connection fitted and violet antenna cable connection fitted: Continue with step 22. F930A303 4 5 5 5 2 2 5 3 3 4 3 3

10. 10 12 832 515 Saab 9-3 CV M04- 33 Remove the battery cover and the battery negative cable. 34 Locate the connector with connected fibre optic cables at the left-hand lower A-pillar (taped to the cable duct) and lift up the connector lock tab. 35 Remove the fibre optic cable from the position in the connector where the arrow points outwards, to the fibre optic cable. 36 Remove the protective cover from the connection to the kit's fibre optic cable and fit the protective cover on the removed fibre optic cable's connec- tion. Carefully move the fibre optic cable aside so that it is not damaged and position it behind the wiring harness. 37 Fit the connection on the fibre optic cable which was fitted in step 31 in the connector and fit the lock tab. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. Important Handle the fibre optic cables with care or the signal may be distorted.  It is very important that the two cables in the connector are not mixed up.  Do not bend the cable in a radius smaller than 25 mm.  Keep the cable ends free from dirt and grime.  The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A309 34 36 34 37

17. 12 832 515 17 Saab 9-3 CV M04- 58 Take the kit's telematics unit and remove any brackets from the telematics unit. 59 Fit the kit's telematics unit in the bracket, a click should be heard, and plug in the connector to the telematics unit. 60 Connect the antenna cable(s) and the bluetooth antenna to the telematics unit. Continue with step 67. Important Handle the fibre optic cables with care or the signal may be distorted.  It is very important that the two cables in the connector are not mixed up.  Do not bend the cable in a radius smaller than 25 mm.  Keep the cable ends free from dirt and grime.  The cable should not lie against any sharp edges as this may cause increased signal reduction. Important Be careful with the bluetooth antenna as it is very easily damaged. F930A316 60 60 60 60 60 59 58 58 59

18. 18 12 832 515 Saab 9-3 CV M04- 61 Raise the soft top and open the boot lid. 62 Disconnect the negative battery cable. 63 Take the kit's telematics unit and remove any brackets from the telematics unit. 64 Remove the connectors from the existing telematics unit and remove the telematics unit. 65 Fit the kit's telematics unit in the bracket, a click should be heard, and plug in the connector to the telematics unit. 66 Connect the antenna cable(s) and the bluetooth antenna to the telematics unit. Proceed to step 73. Important Handle the fibre optic cables with care or the signal may be distorted.  It is very important that the two cables in the connector are not mixed up.  Do not bend the cable in a radius smaller than 25 mm.  Keep the cable ends free from dirt and grime.  The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A317 66 66 66 66 66 65 63 63 65 Important Be careful with the bluetooth antenna as it is very easily damaged.

26. 26 12 832 515 Saab 9-3 CV M04- 85 Cars where the left-hand rear side trim and/or rear seat have been removed: Connect the battery negative cable. 86 Cars where the left-hand rear side trim and/or rear seat have been removed: Lower the soft top completely but allow the soft top cover to remain open. 87 Cars where only the rear seat has been removed: Connect and fit the right-hand bass speaker or fit the right-hand cover. Proceed to step 92. Cars where the left-hand rear side trim and rear seat have been removed: Continue with step 88. 88 Cars where the left-hand rear side trim and rear seat have been removed: Check that the damp protection is intact and replace if neces- sary. Fit the control module in the side trim. 89 Cars where the left-hand rear side trim and rear seat have been removed: Connect the speaker connector, position the side trim and press it down. Check that the rubber protectors are positioned correctly. 90 Cars where the left-hand rear side trim and rear seat have been removed: Fit the screws which hold the side trim, fold the inner lip on the door opening seal over the front edge of the side trim and lift the bracket on the soft top cover seal over the side trim. 91 Cars where the left-hand rear side trim and rear seat have been removed: Fit the speaker grille and fit the bass speakers or the covers. F930A325 89 91 89 88 91 91 91 91 90 90

27. 12 832 515 27 Saab 9-3 CV M04- 92 Cars where the left-hand rear side trim and/or rear seat have been removed: Guide the seat belts in through the belt guide and fit the guides in the backrest cushion by pressing them in. 93 Cars where the left-hand rear side trim and/or rear seat have been removed: Guide in the backrest cushion from above and press it down firmly. 94 Cars where the left-hand rear side trim and/or rear seat have been removed: Fit the two screws for the backrest cushion upper mounting. 95 Cars where the left-hand rear side trim and/or rear seat have been removed: Fit the screws for the seat belts' lower mounting. Tightening torque 45 Nm (33lbf ft) 96 Cars where the left-hand rear side trim and/or rear seat have been removed: Fit the rear head restraints in the sleeves. 97 Cars where the left-hand rear side trim and/or rear seat have been removed: Position the seat cushion and fit the screws in the front edge of the seat cushion. 98 Cars where the left-hand rear side trim and/or rear seat have been removed: Raise the soft top completely. F930A326 97 97 97 97 95 92 92 94 96 96 93

3. 12 832 515 3 Saab 9-3 CV M04- Bus Communication Many parts of the car's electrical system communi- cate using a bus. There are three types of bus communication: P-bus (Powertrain Bus), I-bus (Instrument Bus) and O-bus (Optical bus). The audio system communicates via the O-bus together with the navigation system, the telephone system and others. The O-bus is optical and is a ring bus. Two fibre optical cables are connected to each control module on the bus, one fibre optical cable for receiving and one for sending. Messages received are converted by each control module from a fibre optic signal to electrical and then converted back to optical for sending. The O-bus data transfer rate is 25 Mbit/s. AMP1 is an amplifier behind the left-hand rear side trim AMP2 is an amplifier by the REC CDC is a CD changer by the REC DVD is a DVD player by the REC When fitting new equipment to be connected to the O-bus it is important that it is connected into the correct side of the existing equipment. Important It is very important that everything connected to the O-bus is connected in a specific order, see illustration, and that the ring is closed the whole time. Connection in any other way than that described in these fitting instructions may result in several of the car's systems failing to work. F930A100 1 2 CDC 1 2 DVD 1 2 AMP2 1 2 1 2 AMP2 CDC 1 2 1 2 AMP2 DVD 1 2 1 2 DVD CDC 1 2 1 2 1 2 AMP2 DVD CDC 2 1 Important Handle the fibre optic cables with care or the signal may be distorted.  It is very important that the two leads in the connector are not confused with one another.  Do not splice the cables.  Do not bend the cable in a radius smaller than 25 mm.  Do not expose the cable to temperatures exceeding 85 °C.  Keep the cable ends free from dirt and grime.  Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions.  The cable should not lie against any sharp edges as this may cause increased signal reduction.

Weergaven

  • 411 Totale weergaven
  • 363 Websiteweergaven
  • 48 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 4 52.29.207.161
  • 1 saabpartners.com
  • 2 www.saabpartners.com
  • 2 54.154.214.138