Navigation system 9-3 CV 1

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

6. 6 12 832 516 Saab 9-3 CV M04- 8 Remove the side scuff plate on the right-hand side. 9 Remove the clips for the right-hand side trim and fold the trim aside. Unhook the strap on the rear side of the side trim and remove the side trim. 10 Fold down the soft top completely, but allow the soft top cover to remain open. 11 Open the rear side window on the left-hand side completely. F930A262 8 9 9 9

7. 12 832 516 7 Saab 9-3 CV M04- 12 Remove the screws which hold the rear seat cushion at the front edge. 13 Lift up the cushion and pull it forwards so that it loosens. 14 Pull up both of the rear head restraints to the highest position. 15 Press in the lock on the head restraints' sleeves. Hold the lock pressed in and remove the head restraints. 16 Remove the screws for the seat belts' lower mounting. 17 Remove the two screws for the back rest cush- ion upper mounting. 18 Pull the back rest cushion lower section forwards and lift the back rest cushion upwards. 19 Press out the seat belt guide from the back rest cushion and move the seat belt out from the guide and the back rest cushion. F930A263 13 13 15 15 12 12 16 17 18 19 19

36. 36 12 832 516 Saab 9-3 CV M04- 121 If the luggage compartment right-hand side trim is removed: Position the right-hand side trim and hook on the strap. Fit the clips. 122Fit the left-hand side trim, connect the luggage compartment lighting and hook the strap on. Fit the clips. 123Fit the side scuff plates if they were removed earlier. 124Fit the front section of the luggage compartment trim, the scuff plate and fit the carpet to the luggage compartment floor. F930A292 124 123 124 123 121 121 121 122 122 122 124 124 124 124 124

39. 12 832 516 39 Saab 9-3 CV M04- 133Connect the connector to the kit's control panel. 134Fit the control panel. 135Position and fit the air vent. 136 Cars which did not have an antenna fitted on the boot lid: Fit the microphone in the A-pillar trim on the driver's side, see separate installa- tion instructions. F930A295 134 134 133 135

1. Saab 9-3 CV M04- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 CV M04- Navigation system Accessories Part No. Group Date Instruction Part No. Replaces 12 832 506 12 832 507 12 832 520 12 832 522 9:51-03 Aug 03 12 832 516 12 832 516 Jun 03 F930A259

11. 12 832 516 11 Saab 9-3 CV M04- 34 Cars with antenna cable that runs further forward in the car: Run the thin antenna cable with the blue connector into the torsion compart- ment and up to the centre of the torsion compart- ment. Secure the antenna cable at the existing wiring harness. 35 Cars with antenna cable that runs further forward in the car: Run the thick antenna cable with violet connector through the torsion com- partment. Connect the thick cable to the antenna cable that runs forward in the car and secure them with cable ties to the existing wiring harness. Continue with step 39. F930A267 35 34 34 34

19. 12 832 516 19 Saab 9-3 CV M04- 63 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Remove the protective cover from the fibre optic cable's connection (DVD player - amplifier) and fit the connection in posi- tion 1 in the connector inside the torsion com- partment. Fit the lock. Secure the fibre optic cable along the wiring harness up to the torsion compartment. 64 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Fit the small connector into the large connector and connect the large connector the amplifier. 65 Proceed to step 75. F930A275 64 63 63 64

28. 28 12 832 516 Saab 9-3 CV M04- 96 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Remove the connector from the amplifier and remove the small connector from the amplifier's connector. 97 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Remove the fibre optic cable connected to position 1 in the connector that was removed by opening the lock in the connec- tor and carefully lifting the hook. F930A284 96 97 96 97

29. 12 832 516 29 Saab 9-3 CV M04- 98 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Remove the protective cover from the fibre optic cable's connection (DVD player - amplifier) and fit the connection in posi- tion 1 in the connector that was removed. Fit the protective cover on the fibre optic cable that was removed. Secure the fibre optic cable up to the torsion compartment using cable ties. 99 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Fit the small connector in the large connector and connect the connector to the amplifier. 100Proceed to step 117. F930A285 99 98 98 99

38. 38 12 832 516 Saab 9-3 CV M04- 130Remove the centre air vent in the dashboard by carefully bending in the hooks accessible through the grille. 131Remove the retaining screws for the infotain- ment control panel. 132Remove the control panel and remove the connector. Note Take care to bend the correct hooks. Hooks hold- ing together the air outlet are also visible behind the grille. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm. F930A294 131 131 132 130

18. 18 12 832 516 Saab 9-3 CV M04- 60 Cars without telematics unit in the centre of the torsion compartment: Remove the con- nector from the amplifier. 61 Cars without telematics unit in the centre of the torsion compartment: Unplug the small connector from the large connector. 62 Cars without telematics unit in the centre of the torsion compartment: Remove the fibre optic cable connected to position 1 by opening the lock in the connector and carefully lifting the hook. F930A274 61 62 62 60

22. 22 12 832 516 Saab 9-3 CV M04- 75 Cars without telematics unit in the centre of the torsion compartment: Guide the kit's wiring harness into the torsion compartment. Fit the small connector with the fibre optic cables from the A-pillar and the DVD player into the connector and fit the lock tab. 76 Cars without telematics unit in the centre of the torsion compartment: Fit the connector on the wiring harness inside the torsion compart- ment. Run the kit's wiring harness along the existing wiring harness in the torsion compart- ment and secure them with cable ties. 77 Cars without telematics unit in the centre of the torsion compartment: Locate the connec- tor for the telematics unit in the centre of the torsion compartment and fit the cables from the kit's wiring harness in the connector as follows: Red (RD) cable (+) in position 10 Black (BK) cable (-) in position 20 Fit the connector for the telematics unit in the large connector in the kit's wiring harness. F930A278 75 75 76 BK RD 77

31. 12 832 516 31 Saab 9-3 CV M04- 103 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC with amplifier and/or CD changer: Remove the protective cover from the other connection on the fibre optic cable which was fitted earlier (between the units in the bracket). Fit the connection in position 1 in the small connector. Fit the lock. Fit the protec- tive cover on the fibre optic cable that was removed. 104 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC with amplifier and/or CD changer: Fit the small connector into the connector for the amplifier and the CD changer. 105 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC with amplifier and/or CD changer: Connect the connector for the amplifier and the CD changer. Proceed to step 117. F930A287 103 103 104 103 103 104

34. 34 12 832 516 Saab 9-3 CV M04- 114 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Remove the protective cover from the other connection on the fibre optic cable (between the units in the bracket). Fit the con- nection on the fibre optic cable in position 1 in the small connector for the amplifier and the CD changer. Fit the lock. 115 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Fit the small connector in the connec- tor for the amplifier and the CD changer. 116 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Connect the connector for the ampli- fier and the CD changer. Proceed to step 117. F930A290 114 114 115 114 114 115

2. 2 12 832 516 Saab 9-3 CV M04- 1 DVD player 2 Control panel 3 Fibre optic cable (x1 in kit 12 832 506 and 12 832 507, 455 mm long) (x3 in kit 12 832 520 and 12 832 522) – Between the units in the luggage compart- ment console (455 mm long) – Amplifier - DVD player (1850 mm long) – DVD player - Torsion compartment (1195 mm long) 4 Fibre optic cable (A-pillar - Torsion compart- ment, 2770 mm long) (only in kit 12 832 520 and 12 832 522) 5 Wiring harness with fibre optic cable (only in kit 12 832 520 and 12 832 522) 6 Wiring harness 7 Optical cable connector, 2-pin (x1 in kit 12 832 506 and 12 832 507) (x2 in kit 12 832 520 and 12 832 522) 8 Optical cable connector, 2-pin (only in kit 12 832 506 and 12 832 507) 9 Bracket for telematics unit (only in kit 12 832 520 and 12 832 522) 10 Telematics unit (only in kit 12 832 520 and 12 832 522) 11 Bolt (x2) (only in kit 12 832 520 and 12 832 522) 12 Cable tie (x1 in kit 12 832 506 and 12 832 507) (x17 in kit 12 832 520 and 12 832 522) In addition, the following items are required (ordered separately) • Console for equipment in the luggage compart- ment (certain cars) • Antenna kit (certain cars) • Microphone (certain cars) F930A260 1 12 8 2 7 4 3 6 9 11 5 10

21. 12 832 516 21 Saab 9-3 CV M04- 71 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Fit the kit's fibre optic cable (between the units in the bracket) in position 2 in the kit's connector. 72 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Fit the small connector in the DVD player's connector. 73 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Run the kit's fibre optic cable (DVD player - torsion compartment) forward along the existing wiring harness. Secure with cable ties but do not tighten them completely as a further 2 cables shall be secured. 74 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Remove the protective cover from the fibre optic cable's con- nection (DVD player - torsion compartment) and fit it in position 2 in the small connector inside the torsion compartment. Proceed to step 75. F930A277 71,74 72 73 71,74

23. 12 832 516 23 Saab 9-3 CV M04- 78 Cars without telematics unit in the centre of the torsion compartment: Guide the loose ends of the kit's wiring harness through the previously fitted cable ties along the fibre optic cable fitted earlier (DVD player - torsion com- partment) forward to the wiring harness branch- ing to the REC. Tighten the cable ties. 79 Cars without telematics unit in the centre of the torsion compartment: Remove the tape which secures the connector for the telematics unit power supply by the wiring harness and unplug the connector. 80 Cars without telematics unit in the centre of the torsion compartment: Remove the lock and fit the cables from the kit's wiring harness in the connector as follows: Red (RD) cable (+) in position 1 Black (BK) cable (-) in position 2 81 Cars without telematics unit in the centre of the torsion compartment: Fit the lock, connect the connector and secure it at the wiring harness to the REC. F930A279 78 RD 79 BK 80 80

26. 26 12 832 516 Saab 9-3 CV M04- 88 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Fit the kit's fibre optic cable (DVD player - torsion compartment) in position 1 in the kit's connector. 89 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Fit the kit's fibre optic cable (DVD player - amplifier) in position 2 in the kit's connector. 90 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Fit the small connector in the DVD player's connector. 91 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Fit the kit's fibre optic cables (DVD player - torsion compartment and DVD player - amplifier) forward along the existing wiring harness. Secure with cable ties. F930A282 88,89 88 90 91 89

30. 30 12 832 516 Saab 9-3 CV M04- 101 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Continue with step 117. Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC with amplifier or CD changer: Remove the connector for the amplifier and the CD changer and unplug the small connector from the large connector. Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC with amplifier and CD changer: Remove the connector for the CD changer and unplug the small connector from the large connector. 102 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC with amplifier and/or CD changer: Remove the fibre optic cable which is connected to position 1 in the connector that was removed by opening the lock in the connector and carefully lifting the hook. Carefully guide the fibre optic cable away so that it is not damaged. F930A286 101 102 102

33. 12 832 516 33 Saab 9-3 CV M04- 110 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Remove the fibre optic cable con- nected to position 1 in the connector that was removed by opening the lock in the connector and carefully lifting the hook. 111 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Fit the connection on the fibre optic cable in position 1 in the kit's connector. 112 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Remove the protective cover from the connection on the kit's fibre optic cable (between the units in the bracket) and fit the connection on the fibre optic cable in position 2 in the kit's connector. 113 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and/or CD changer: Fit the small connector in the DVD player's connector. F930A289 111,112 111 113 112 110

17. 12 832 516 17 Saab 9-3 CV M04- 55 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Fit the kit's fibre optic cable (DVD player - torsion compartment) in position 1 in the kit's small connector. 56 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Fit the kit's fibre optic cable (DVD player - amplifier) in position 2 in the kit's small connector. 57 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Fit the small connector in the DVD player's connector. 58 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Run the kit's fibre optic cables (DVD player - torsion compartment and DVD player - amplifier) forward along the exist- ing wiring harness and secure with cable ties. Do not tighten the cable ties completely as a further 2 cables shall be secured. 59 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Remove the protective cover from the fibre optic cable's connection (DVD player - torsion compartment) and fit the connec- tion in position 2 in the small connector inside the torsion compartment. F930A273 55 55 57 58 56,59

25. 12 832 516 25 Saab 9-3 CV M04- 84 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Disconnect the battery negative cable. Fit the clip nut in the square hole by the REC and fit the bracket in the luggage compartment. 85 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Locate the connector for the DVD player by the REC. 86 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Connect the kit's wiring harness to the connector. 87 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Remove the protective covers from the connections in one end of the kit's fibre optic cables (DVD player - torsion compartment and DVD player - amplifier). WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm. F930A281 84 84 85 86

4. 4 12 832 516 Saab 9-3 CV M04- 1 Connect the diagnostic tool and disconnect the infotainment system control panel from the car. Go into the menu “All” and choose the control module under “Add/Remove”. Then choose “Remove” and follow the instructions. The igni- tion key must be in the ON position. TIS 2000 may need to be used. When the control module is separated from the car the ignition key must be turned to the OFF position. Following which the control module can be removed. Important In cars where the left-hand front seat is electrically adjustable and there is no bracket at the rear fuse box, the left-hand front seat must be positioned in its most forward position and with the backrest folded forwards. Important The control module is sensitive to electrostatic discharges. To avoid damaging the internal compo- nents in the control module, a replacement must be made with care in the following way: • Never touch the pins on a control module with hands or clothes. • Ground yourself by touching the car's body/ engine. Remove the connector on the car's control module. • Ground yourself by touching the car's body/ engine. Connect the connector on the car's control module. • Deposit the replaced control module in the returns packaging without touching its pin. • Keep the new control module in its packaging as long as possible.

8. 8 12 832 516 Saab 9-3 CV M04- 20 Carefully remove the speaker grille from the left- hand rear side trim. Use removal tool 82 93 474. 21 Remove the screw that holds the rear side trim on the left-hand side. 22 Lift the side trim upwards. Retain the rubber protectors. 23 Unhook the control module from the side trim, but do not remove the control module connector as this means a diagnostic trouble code being generated. 24 Remove the speaker connector and remove the side trim. Remove the bass speakers or the covers. 25 Raise the soft top and check one more time from the luggage compartment if there is any connec- tion for the antenna cable in the centre of the torsion compartment and if a telematics unit is fitted in the centre of the torsion compartment. No antenna cable connection: Fit antenna to boot lid, see separate installation instructions and then continue with step 39. There is only one violet antenna cable connection, and there is no telematics unit: Continue with step 26. There is only one blue antenna cable connection and there is no telematics unit: Continue with step 39. There is only one violet antenna cable connection and there is a telematics unit: Continue with step 26. There are two antenna cable connections but there is no telematics unit: Continue with step 39. There are two antenna cable connections, there is a telematics unit, but there is no bracket by the REC: Continue with step 84. F930A264 20 21 22 24 23 24 24 24 24

9. 12 832 516 9 Saab 9-3 CV M04- 26 There is only one violet antenna cable connection: Remove the boot lid trim as follows: – US: Remove the emergency opening handle – Remove the closing handle on the inside of the boot lid, the two-stage rivets and the boot lid trim. – US: Remove the screws of the emergency opening mechanism and move the mecha- nism aside. 27 There is only one violet antenna cable connection and the antenna is fitted on the boot lid: Remove the antenna cable from the antenna and remove the antenna. 28 Cars with an antenna cable that runs further than the centre of the torsion compartment: Continue with step 36. Cars with antenna cable that runs further forward in the car: Continue with step 29. F930A265 26 26 26 26 27

20. 20 12 832 516 Saab 9-3 CV M04- 66 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Remove the bracket and move it out to facilitate access. 67 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Locate the connector for the DVD player by the REC. 68 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Connect the kit's wiring harness to the connector. 69 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Remove the protective cover from the other connection on the kit's fibre optic cable (DVD player - torsion compartment). 70 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Fit the kit's fibre optic cable (DVD player - torsion compartment) in position 1 in the kit's connector. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm. F930A276 67 68 70

12. 12 12 832 516 Saab 9-3 CV M04- 36 Cars with antenna cable that runs on to the centre of the torsion compartment: Take the antenna from the kit and run the antenna cables through the hole in the boot lid. Fit the antenna. Tightening torque 2 Nm (1.5 lbf ft) 37 Cars with antenna cable that runs on to the centre of the torsion compartment: Remove the existing antenna cable completely. 38 Cars with antenna cable that runs on to the centre of the torsion compartment: Fit the kit's antenna cable in the boot lid and connect it to the antenna. Run the kit's antenna cable along the same route as the old cable up to the torsion compartment. Secure the antenna cable to the existing wiring harness using cable ties. Note The boot lid must be closed and the soft top cover open in order to gain access to the whole antenna cable. Note The boot lid must be closed and the soft top cover open in order to gain access to the whole antenna cable. F930A268 38 38 38 38 38 38 38 38 38 38 38 38 38 38 36 38 38 38 38

32. 32 12 832 516 Saab 9-3 CV M04- 106 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC: Disconnect the battery negative cable. Remove the bracket and move it out to facilitate access. 107 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC: Locate the connector for the DVD player by the REC. 108 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC: Connect the kit's wiring harness to the connector. 109 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier or CD changer: Remove the connector for the ampli- fier and the CD changer and unplug the small connector from the large connector. Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC with amplifier and CD changer: Remove the connector for the CD changer and unplug the small connector from the large connector. F930A288 107 108 109 WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm.

37. 12 832 516 37 Saab 9-3 CV M04- 125 US cars where the boot lid trim is removed: Fit the emergency opening mechanism. 126 If the boot lid trim is removed: Fit the trim on the inside of the boot lid, fit the two-stage rivets and fit the closing handle. US cars where the boot lid trim is removed: Fit the emergency handle. 127 If the boot lid trim has been removed: Close the boot lid. 128 Cars without telematics unit in the centre of the torsion compartment: Fit the A-pillar trim. 129 Cars without telematics unit in the centre of the torsion compartment: Fit the scuff plate. F930A293 126 126 126 125 129 128

40. 40 12 832 516 Saab 9-3 CV M04- 137 Cars where the left-hand rear side trim and rear seat have been removed: Connect the battery negative cable. 138 Cars where the left-hand rear side trim and rear seat have been removed: Lower the soft top completely but allow the soft top cover to remain open. 139 Cars where the left-hand rear side trim and rear seat have been removed: Check that the damp protection is intact and replace if neces- sary. Fit the control module in the side trim. 140 Cars where the left-hand rear side trim and rear seat have been removed: Connect the speaker connector, position the side trim and press it down. Check that the rubber protectors are positioned correctly. 141 Cars where the left-hand rear side trim and rear seat have been removed: Fit the screw that holds the side trim, bend the inner lip of the door opening seal over the front edge of the side trim and lift the bracket on the soft top cover seal over the side trim. 142 Cars where the left-hand rear side trim and rear seat have been removed: Fit the speaker grille and the bass speakers or the covers. F930A296 141 140 142 140 139 142 142 142 142

13. 12 832 516 13 Saab 9-3 CV M04- 39 Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC: Continue with step 40. Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Continue with step 40. Cars without telematics unit in the centre of the torsion compartment: Continue with step 41. 40 Connect the antenna cable with blue connector to the telematics unit. Cars with telematics unit in the centre of the torsion compartment and where the bracket is fitted by the REC: Continue with step 106. Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Continue with step 84. 41 Cars without telematics unit in the centre of the torsion compartment: Remove the left- hand scuff plate. 42 Cars without telematics unit in the centre of the torsion compartment: Remove the lower section of the A-pillar trim on the left-hand side. F930A269 40 42 41 40

14. 14 12 832 516 Saab 9-3 CV M04- 43 Cars without telematics unit in the centre of the torsion compartment: Set the left-hand front seat in the forward position and fold the backrest forward. 44 Cars without telematics unit in the centre of the torsion compartment: Take the longest fibre optic cable from the kit and run it from the connector at the left-hand lower A-pillar via the wiring harness by the sill, under the rear seat and forwards on to the left-hand roll bar in the torsion compartment. Secure the fibre optic cable using cable ties. Note The seat must be pushed to the rear position in order to access the whole route. Following which, push the seat back to the forward position. F930A270 44 44 44 Important Handle the fibre optic cables with care or the signal may be distorted. • Do not bend the cable in a radius smaller than 25 mm. • The cables must not be exposed to knocks which cause the transparent plastic to whiten, which means that the light intensity is weak- ened. Such damage can cause an interruption to communication. • The cable should not lie against any sharp edges as this may cause increased signal reduction.

16. 16 12 832 516 Saab 9-3 CV M04- 50 Cars without telematics unit in the centre of the torsion compartment: Fit the other con- nection on the kit's fibre optic cable in position 1 in the kit's connector. 51 Cars without telematics unit in the centre of the torsion compartment but where the bracket is fitted by the REC: Continue with step 66. Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Fit the clip nut in the square hole by the REC and fit the bracket in the luggage compartment. 52 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Locate the connec- tor for the DVD player by the REC. 53 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Connect the kit's wiring harness to the connector. 54 Cars without telematics unit in the centre of the torsion compartment and without bracket fitted by the REC: Remove the protective covers from the connections at one end of the kit's fibre optic cables (DVD player - torsion compartment and DVD player - amplifier). F930A272 51 51 52 53 50 WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm.

24. 24 12 832 516 Saab 9-3 CV M04- 82 Cars without telematics unit in the centre of the torsion compartment: Take the kit's telematics unit and remove any brackets from the telematics unit. 83 Cars without telematics unit in the centre of the torsion compartment: Fit the kit's telemat- ics unit into the bracket, a click must be heard, and connect the connector and the thin antenna cable with the blue connector to the telematics unit. Secure the violet connector for the thick antenna cable (if it does not require connecting) by the wiring harness. Proceed to step 101. Important Handle the fibre optic cables with care or the signal may be distorted. • It is very important that the two cables in the connector are not mixed up. • Do not bend the cable in a radius smaller than 25 mm. • Keep the cable ends free from dirt and grime. • The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A280 83 83 83 82 82 83

5. 12 832 516 5 Saab 9-3 CV M04- 2 Raise the soft top and open the boot lid. 3 Remove the carpet on the luggage compartment floor and remove the luggage compartment scuff plate. 4 Remove the rivets and lift out the front section of the luggage compartment trim. 5 Remove the side scuff plate on the left-hand side. 6 Remove the clips for the left-hand side trim and fold the trim aside. Unhook the strap on the rear side of the side trim and remove the connector from the luggage compartment lighting. Remove the side trim. 7 Check from the luggage compartment if there is a connection for the antenna cable in the centre of the torsion compartment and if a telematics unit is fitted in the centre of the torsion compart- ment. If there is a telematics unit fitted then it must be removed without the connector being removed. No antenna cable connection: Fit antenna to boot lid, see separate installation instructions and then continue with step 8. There is only one violet antenna cable connection and there is no telematics unit: Continue with step 8. There is only one blue antenna cable connection and there is no telematics unit: Continue with step 10. There is only one violet antenna cable connection, there is a telematics unit, but there is no bracket by the REC: Continue with step 8. There is only one violet antenna cable connection, there is a telematics unit, and there is a bracket by the REC: Replace the antenna on the boot lid, see separate installa- tion instructions and then continue with step 8. There are two antenna cable connections, but there is no telematics unit: Continue with step 10. There are two antenna cable connections, there is a telematics unit, but there is no bracket by the REC: Continue with step 10. There are two antenna cable connections, there is a telematics unit and there is a bracket by the REC: Continue with step 106. F930A261 5 6 6 6 3 3 6 4 4 4 4 4

10. 10 12 832 516 Saab 9-3 CV M04- 29 Cars with antenna cable that runs further forward in the car: Take the antenna from the kit and run the antenna cables through the hole in the boot lid. Fit the antenna. Tightening torque 2 Nm (1.5 lbf ft) 30 Cars with antenna cable that runs further forward in the car: Remove the existing antenna cable completely. 31 Cars with antenna cable that runs further forward in the car: Fit the kit's antenna cable in the boot lid and connect it to the antenna. Run the kit's antenna cable along the same route as the old cable up to the torsion compartment. 32 Cars with antenna cable that runs further forward in the car: Secure the antenna cable to the existing wiring harness using cable ties. 33 Cars with antenna cable that runs further forward in the car: Divide the two antenna cables up to the fastener. Note The boot lid must be closed and the soft top cover open in order to gain access to the whole antenna cable. Note The boot lid must be closed and the soft top cover open in order to gain access to the whole antenna cable. F930A266 32 32 32 32 32 32 32 32 32 32 32 32 32 32 29 33 33

3. 12 832 516 3 Saab 9-3 CV M04- Bus Communication Many parts of the car's electrical system communi- cate using a bus. There are three types of bus com- munication: P-bus (Powertrain Bus), I-bus (Instru- ment Bus) and O-bus (Optical bus). The audio system communicates via the O-bus together with the navigation system, the telephone system and others. The O-bus is optical and is a ring bus. Two fibre optical cables are connected to each control module on the bus, one fibre optical cable for receiving and one for sending. Messages received are converted by each control module from a fibre optic signal to electrical and then converted back to optical for sending. The O-bus data transfer rate is 25 Mbit/s. AMP1 is an amplifier behind the left-hand rear side trim AMP2 is an amplifier by the rear fuse box CDC is a CD changer by the rear fuse box DVD is a DVD player by the rear fuse box When fitting new equipment to be connected to the O-bus it is important that it is connected into the cornsrect side of the existing equipment. Important It is very important that everything connected to the O-bus is connected in a specific order, see illustration, and that the ring is closed the whole time. Connection in any other way than that described in these fitting instructions may result in several of the car's systems failing to work. F930A100 1 2 CDC 1 2 DVD 1 2 AMP2 1 2 1 2 AMP2 CDC 1 2 1 2 AMP2 DVD 1 2 1 2 DVD CDC 1 2 1 2 1 2 AMP2 DVD CDC 2 1 Important Handle the fibre-optic cables with care or the signal may be distorted. • It is very important that the two leads in the connector are not confused with one another. • Do not splice the cables. • Do not bend the cable in a radius smaller than 25 mm. • Do not expose the cable to temperatures exceeding 85 °C. • Keep the cable ends free from dirt and grime. • Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. • The cable should not lie against any sharp edges as this may cause increased signal reduction.

27. 12 832 516 27 Saab 9-3 CV M04- 92 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Remove the connector inside the torsion compartment. Lift up the lock tab and remove the small connector. 93 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Remove the fibre optic cable connected to position 2 by opening the lock in the connector and carefully lifting the hook. 94 Cars with telematics unit in the centre of the torsion compartment but without bracket fit- ted by the REC: Remove the protective cover from the fibre optic cable's connection (DVD player - torsion compartment) and fit the connection in position 2. Fit the protective cover on the fibre optic cable that was removed. 95 Cars with telematics unit in the centre of the torsion compartment but without bracket fitted by the REC: Fit the small connector into the connector. Fit the lock tab and fit the connec- tor inside the torsion compartment. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm. Important Handle the fibre optic cables with care or the signal may be distorted. • It is very important that the two cables in the connector are not mixed up. • Do not bend the cable in a radius smaller than 25 mm. • Keep the cable ends free from dirt and grime. • The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A283 92,95 92,95 93 93,94

35. 12 832 516 35 Saab 9-3 CV M04- 117 Fit the DVD player in the bracket, a clicking sound should be heard, connect the DVD player and fit the bracket. 118 Fit the bracket. Tighten the nut on the bracket's top side. 119 Secure the kit's wiring harness to the car's wiring harness. 120Position the bracket for the telematics unit in the torsion compartment and fit it. Important Handle the fibre optic cables with care or the signal may be distorted. • It is very important that the two cables in the connector are not mixed up. • Do not bend the cable in a radius smaller than 25 mm. • Keep the cable ends free from dirt and grime. • The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A291 118 118 118 118 120 120 117 Important Handle the fibre optic cables with care or the signal may be distorted. • It is very important that the two cables in the connector are not mixed up. • Do not bend the cable in a radius smaller than 25 mm. • Keep the cable ends free from dirt and grime. • The cable should not lie against any sharp edges as this may cause increased signal reduction.

41. 12 832 516 41 Saab 9-3 CV M04- 143 Cars where the left-hand rear side trim and rear seat have been removed: Guide the rear seat belts into the belt guides and fit the guides in the backrest cushion by pressing them in. 144 Cars where the left-hand rear side trim and rear seat have been removed: Position the backrest cushion from above and press it down securely. 145 Cars where the left-hand rear side trim and rear seat have been removed: Fit the two screws for the upper mounting of the backrest cushion. 146 Cars where the left-hand rear side trim and rear seat have been removed: Fit the screws for the lower mounting of the seat belts. 147 Cars where the left-hand rear side trim and rear seat have been removed: Fit the rear head restraints in the sleeves. 148 Cars where the left-hand rear side trim and rear seat have been removed: Position the seat cushion and fit the screws in the front edge of the seat cushion. 149 Cars where the left-hand rear side trim and rear seat have been removed: Raise the soft top completely. Proceed to step 151. 150Connect the battery negative cable if not done already. 151Adjust the time and date. 152Synchronise remote control code by inserting the key into the ignition. 153Activate window lift pinch protection function by operating the side windows up and down twice. An audible confirmation will sound when activa- tion is complete. 154 Cars where the left-hand front seat is electri- cally adjustable: Reset the position of the seat if it has been changed. 155Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 156Place the map disc in the DVD player, check the system by test driving the car until the naviga- tion system makes contact with the satellites. The map should display on the screen. F930A297 148 148 148 148 146 143 143 145 147 147 144 Important Repeat this procedure with all keys. Otherwise, the remote controls will not function. Note The diagnostic tool will on some occasions need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display.

15. 12 832 516 15 Saab 9-3 CV M04- 45 Cars without telematics unit in the centre of the torsion compartment: Disconnect the battery negative cable. Locate the loose fibre optic cable and the connector with the fibre optic cables connected at the left-hand lower A-pillar (taped to the cable duct) and lift up the connec- tor's lock tab. 46 Cars without telematics unit in the centre of the torsion compartment: Remove the fibre optic cable from the position in the connector where the arrow points outward, to the fibre optic cable. 47 Cars without telematics unit in the centre of the torsion compartment: Remove the protec- tive cover from the connection to the kit's fibre optic cable. 48 Cars without telematics unit in the centre of the torsion compartment: Fit the protective cover to the connection of the fibre optic cable that was removed, carefully guide the fibre optic cable away so that it is not damaged and position it behind the wiring harness. 49 Cars without telematics unit in the centre of the torsion compartment: Fit the connection on the new fibre optic cable in the connector and fit the lock tab. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector when in close proximity to them. The eyes can be damaged if the distance between the light source and the eyes is less than 20 mm. F930A271 45 48 45 49 Important Handle the fibre optic cables with care or the signal may be distorted. • It is very important that the two cables in the connector are not mixed up. • Do not bend the cable in a radius smaller than 25 mm. • Keep the cable ends free from dirt and grime. • The cable should not lie against any sharp edges as this may cause increased signal reduction.

Weergaven

  • 511 Totale weergaven
  • 432 Websiteweergaven
  • 79 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 5

  • 9 www.saabpartners.com
  • 4 saabpartners.com
  • 1 52.29.207.161
  • 1 52.211.236.180
  • 2 54.154.214.138