Parking assistance (SPA) 9-3

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

2. 2 12 788 454 Saab 9-3 M03- 1 SPA control module 2 Holder (x4) 3Seal (x4) 4 Distance sensor (x4) 5 Moulding, bumper 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Dust cover 9 Cable tie (x2) F930A054 1 9 5 7 6 2 3 4 8

3. 12 788 454 3 Saab 9-3 M03- 1 Disconnect the negative cable from the battery and raise the vehicle. 2 Remove the two nuts holding the air shield of the rear bumper against the body. Remove the two screws holding the bumper shell against the wheel housings. 3 Lower the vehicle and remove the rear bumper trim moulding. 4 Open the hatchback. F930A044 2 2 2 3

4. 4 12 788 454 Saab 9-3 M03- 5 Lift up and fold aside the luggage compartment floor and remove the luggage compartment scuff plates. 6 Remove the hatches from the luggage compart- ment side trims. 7 Remove the scuff plates from the side frames. 8 Remove the clip for the left-hand side trim and move the trim aside. 9 Remove the rear lamp cluster. F930A045 6 7 9 9 8 8

8. 8 12 788 454 Saab 9-3 M03- 18 Plug in the control module and fit it onto the mounting point on the rear electrical centre. 19 Remove the support from the bumper shell. F930A049 19 18

5. 12 788 454 5 Saab 9-3 M03- 10 Remove the bumper shell screws that are locat- ed below the rear lamp cluster. 11 Remove the bumper bolts at the wheel housings. 12 Remove the bumper shell by first pulling the side pieces outwards and then pulling the bump- er shell rearwards. 13 Remove the sound insulation from behind the right-hand wheel housing. Important Place the bumper on a clean, soft surface. F930A046 10 13 12 11

7. 12 788 454 7 Saab 9-3 M03- 17 Fit the new wiring harness. Connect the wiring harness with reference to the notes from the preceding point. Fit a new dust cover and secure the harness components with a cable tie. Important The harness attachment under the rear light should not be fitted yet as the sound insulation uses the same attachment. F930A048 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17

9. 12 788 454 9 Saab 9-3 M03- 20 Fit the bumper-shell trim-moulding with the help of the guide tabs and clip in the hooks, begin- ning at the centre and working outwards. 21 Fit the seals to the sensors. 22 Fit together the distance sensors and the holders. 23 Fit the distance sensors to the mountings on the trim moulding. 24 Connect the sensor wiring harness to the sen- sors and fit it into the slots in the bumper shell. 25 Fit the support to the bumper shell. Important The connector sockets on the sensors should point towards the right-hand side of the vehicle. F930A050 21 22 23 25 24 24 24

11. 12 788 454 11 Saab 9-3 M03- 31 Fit the sound insulation behind the right-hand wheel housing and snap into place the harness fastening under the right-hand rear light. 32 Fit the console in which such equipment as a CD changer may be fitted. Plug in the connec- tions to any equipment in the console. 33 Fit the left-hand side trim. 34 Fit the scuff plates to the side frames. 35 Fit the hatches in the luggage compartment side trims. 36 Fit the scuff plates and fold down the luggage compartment floor. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A052 34 33 33 31 35 31

6. 6 12 788 454 Saab 9-3 M03- 14 Remove the rubber plug from under the left- hand rear light. 15 Remove the console in which such equipment as a CD changer may be fitted. Disconnect the connections to any equipment in the console. 16 Remove the rearmost connector (blue) from the rear electrical centre. Make a note of how the rear wiring harness is connected and then remove it. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A047 16 16 16 16 16 16 16 16 14 16 16 16 16 16 16

1. Saab 9-3 M03- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 M03- Parking assistance (SPA) Accessories Part No. Group Date Instruction Part No. Replaces 12 787 887 9:40-03 Oct 02 12 788 454 12 788 454 Jul 02 F930A042

10. 10 12 788 454 Saab 9-3 M03- 26 Lift up the bumper shell and thread the wiring harness through the hole under the left-hand rear light. Fit the grommet. 27 Fit the two tabs of the bumper shell under the holders and the outer corners between the wheel arch liner and the holder at the wheel housings. Press the bumper shell into place. 28 Plug in the parking assistance harness connec- tor and fit the connector into the hole beside the left-hand rear light. Fasten the wiring harness with a cable tie. 29 Fit the bumper shell screws which are located below the rear lamp cluster. 30 Fit and connect the rear lamp cluster. Check the fit against the boot lid moulding. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A051 30 30 30 27 27 28 26 F930A051 28

12. 12 12 788 454 Saab 9-3 M03- 37 Raise the car. 38 Fit the bumper bolts at the wheel housings. 39 Fit the two nuts holding the rear bumper air shield against the body. 40 Lower the car. 41 Close the boot lid. 42 Check the fit of the bumper. Adjust as necessary. 43 Connect the negative battery cable. 44 Adjust the time and date. 45 Synchronise the remote control code by putting the key in the ignition. 46 Activate the window lifts' pinch protection by running the side windows up and down twice. A sound is made to verify activation. 47 Connect the diagnostic tool, select car and mod- el year, select “All”, select “Add/Remove”, select the accessory and then “Add”. Important This must be carried out with all remote controls, otherwise they will not work. Note The diagnostic tool needs to obtain a security code in TIS at certain times. Information on what to do will be displayed on the diagnostic tool screen. F930A053 39 39 38 38

Weergaven

  • 684 Totale weergaven
  • 559 Websiteweergaven
  • 125 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 7 saabpartners.com
  • 31 www.saabpartners.com
  • 4 52.29.207.161
  • 4 54.154.214.138