Parking assistance (SPA) 9-3 2

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

7. 32 025 940 7 Saab 9-3 19 Remove the rubber plug from under the left- hand rear lamp cluster. 20 Connect the ground cable. 21 Connect the control module and fit it into the slots on the rear fuse box. 22 Position the wiring harness and secure with cable ties. F930A631 19 22 22 22 22 21 20

15. 32 025 940 15 Saab 9-3 1 Turn the ignition key to the OFF position and remove the key. 2 Raise the car. 3 Remove the spoiler's centre nuts. 4 Remove the screws to the wheel housing. 5 Lower the car and open the tailgate. 6 Insert a screwdriver in the hole to reach under the catch for the bumper shell. Bend up using the screwdriver to release the catch. F930A405 3 3 6 4 4

22. 22 32 025 940 Saab 9-3 22 Fold down the rear seat backrests. 23 Remove the left-h and C-pillar trim. Use 82 93 474 Removal tool to remove the cover plate. 24 Remove the left-hand side bolster. Use 82 93 474 Removal tool to remove the clips. F930A643 23 23 23 24 24 24

26. 26 32 025 940 Saab 9-3 38 Connect the ground cable to the grounding point. 39 Fit the kit's control module on the bracket by the electrical centre and plug in the connectors. 40 Position the wiring harn ess and fit the straps. F930A647 38 40 40 40 40 39

27. 32 025 940 27 Saab 9-3 41 Fit the luggage compartment lighting. 42 Press the side trim into its clips. 43 Fit the cover over the storage compartment. 44 Fit the screw. 45 Fit the cover. 46 Fit the mounting for the cargo guard (if fitted). 47 Fit the two-stage rivet. 48 Fit the clip to the mounting in the body. F930A648 43 44 41 45 46 47 48

29. 32 025 940 29 Saab 9-3 52 Fit the left-hand side bolster. Check that the belt is not twisted. 53 Fit the left-hand C-pillar trim. 54 Fold up the backrests. F930A650 53 53 53 52 52 52

24. 24 32 025 940 Saab 9-3 28 Remove the clip from the mounting in the body. Use a screwdriver. 29 Remove the two-stage rivet using 84 71 179 Removal tool, clips. 30 Remove the mounting for the cargo guard (if fit- ted). 31 Remove the cover and the screw. 32 Lift the cover away from over the storage com- partment. 33 Remove the luggage compartment lighting lens and insert the bulb holder through the hole in the side trim. 34 Remove the trim so that the clips release. F930A645 32 31 33 31 30 29 28

33. 32 025 940 33 Saab 9-3 6 Remove the carpet on the luggage compart- ment floor and remove the luggage compart- ment scuff plates. 7 Remove the left-hand side scuff plate. 8 Remove the left-hand side trim's clips and move the trim aside. Unhook the strap on the rear of the side trim (certain cars) and unplug the con- nector from the luggage compartment lighting. Remove the side trim. F930A654 8 6 6 7 8

36. 36 32 025 940 Saab 9-3 17 Remove the rubber plug from under the left- hand rear lamp cluster. 18 Fit the ground cable. 19 Position the new wiring harness and secure the wiring harness with cable ties. 20 Connect the control module and fit it into the slots on the rear fuse box. F930A657 17 18 19 20 19 19 19 18 19 19

3. 32 025 940 3 Saab 9-3 1 Open the boot lid. 2 Turn the ignition key to the OFF position and remove the key. Raise the car. 3 Remove the two nuts holding the rear bumper air shield against the body and the two bolts holding the bumper shell against the wheel housings. 4 Lower the car. 5 M03-07: Remove the decor strip from the rear bumper. F930A627 3 3 3 5

16. 16 32 025 940 Saab 9-3 7 Pull the bumper shell away from the holders. 8 Release the catches using a screwdriver. Detach the shell from the moulding. 9 Lift off the bumper shell. Important Place the bumper on a soft, clean surface. F930A406 8 9 7

17. 32 025 940 17 Saab 9-3 10 Pull the cellular block from the bumper shell lugs. 11 M06-07: Remove the corner protective mould- ings and the protective shell by inserting tool 82 93 474 under the shell to release the clips. F930A407 11 10 11 11 11

6. 6 32 025 940 Saab 9-3 15 Remove the console in which such equipment as a CD changer/amplifier may be fitted. Dis- connect the connections to any equipment in the console. 16 Remove the connector for the rear harness (blue) from the fuse box. Unplug connector A1 from the blue connector. Remove the lock. 17 Fit the kit's wiring harness. Fit the red cable to connector A1 in position 1. Fit the green cable to connector A1 in position 4. 18 Fit the lock. Plug connector A1 into the blue con- nector. WARNING Certain cars: The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connect or at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A630 17 16,18 16 16,18

23. 32 025 940 23 Saab 9-3 25 Remove the luggage compartment floor. 26 Cars with subwoofer: Lift up the subwoofer. 27 Remove the scuff plate's clips using 84 71 179 Removal tool, clips and lift up the scuff plate. F930A644 27 27 25 25

25. 32 025 940 25 Saab 9-3 35 Remove the connector for the rear harness (blue) from the fuse box. Unplug connector A1 from the blue connector. Remove the lock. 36 Fit the kit's wiring harness. Fit the red cable to connector A1 in position 1. Fit the green cable to connector A1 in position 4. 37 Fit the lock. Plug connector A1 into the blue con- nector. WARNING The wiring harness must be routed and secured so that it cannot become trapped or chafe against anything when refitting dismantled parts. Incorrect routing could cause damage to the wiring harness and short circuit/fire. F930A646 36 35,37 35 35,37

28. 28 32 025 940 Saab 9-3 49 Fit the scuff plate. 50 Cars with subwoofer: Lower the subwoofer and screw it in. 51 Fit the luggage compartment floor. F930A649 49 49 51 51

9. 32 025 940 9 Saab 9-3 30 M08: Drill 8 mm holes (from the inside of the bumper shell) in the centre of each marking (x 4). Position the hole-punching tool from the outside of the bumper. Grip on the outside, at the same time tighten the nut from the inside until the hole-punching tool is pressed through the whole of the bumper shell. Carry out the hole-making procedure for all four holes. Fit the tape and holders for the sensors in accordance with the markings in the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. F930A633

18. 18 32 025 940 Saab 9-3 12 M08: Drill 8 mm holes (from the inside of the bumper shell) in the centre of each marking (x 4). Position the hole-punching tool from the outside of the bumper. Grip on the outside, at the same time tighten the nut from the inside until the hole-punching tool is pressed through the whole of the bumper shell. Carry out the hole-making procedure for all four holes. Fit the tape and holders for the sensors in accordance with the markings in the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. F930A633

32. 32 32 025 940 Saab 9-3 1 Open the boot lid. 2 Turn the ignition key to the OFF position and remove the key. Raise the car. 3 Remove the two nuts that hold the rear bumper air shield to the body and the bolts that hold the bumper shell to the wheel housings. 4 Lower the car. 5 M04-07: Remove the rear bumper's decor strip. F930A653 3 3 3 3 5

35. 32 025 940 35 Saab 9-3 13 Remove the console in which equipment such as a CD-changer may be fitted. Disconnect the connections to any equipment in the console. 14 Remove the connector for the rear harness (blue) from the fuse box. Unplug connector A1 from the blue connector. Remove the lock. 15 Fit the kit's wiring harness. Fit the red cable to connector A1 in position 1. Fit the green cable to connector A1 in position 4. 16 Fit the lock. Plug connector A1 into the blue con- nector. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A656 15 14,16 14 14,16

41. 32 025 940 41 Saab 9-3 35 Fit the console in which such equipment as a CD changer/amplifier may be fitted. Plug in the connections to any equipment in the console. 36 Align the left-hand side trim, connect the lug- gage compartment lighting and hook in any strap. Fit the clips. 37 Fit the side scuff plates. 38 Fit the scuff plate and fit the carpet on the lug- gage compartment floor. WARNING Certain cars: The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connect or at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A661 36 36 38 38 37

1. Saab 9-3 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 Parking assistance (SPA) 4D, see page 2-13 5D, see page 14-30 CV, see page 31-42 Accessories Part No. Group Date Instruction Part No. Replaces 32 025 902 32 025 903 32 025 904 32 026 045 9:40-08 May 07 32 025 940 32 025 940 Oct 06 F930A042

4. 4 32 025 940 Saab 9-3 6 M03-07: Raise and fold aside the luggage com- partment floor and remove the luggage com- partment scuff plate. 7 Remove the panel in the luggage compartment side trim. 8 M03-07: Remove the side scuff plates. 9 Remove the clips and fold aside the side trims on the left and right-hand sides. 10 Remove the rear lamp clusters. F930A628 8 10 9 9 10 6 6

38. 38 32 025 940 Saab 9-3 27 M08: Drill 8 mm holes (from the inside of the bumper shell) in the centre of each marking (x 4). Position the hole-punching tool from the outside of the bumper. Grip on the outside, at the same time tighten the nut from the inside until the hole-punching tool is pressed through the whole of the bumper shell. Carry out the hole-making procedure for all four holes. Fit the tape and holders for the sensors in accordance with the markings in the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. F930A633

21. 32 025 940 21 Saab 9-3 19 Fit the cellular block by guiding it in toward the bumper shell lugs. Press the cellular block in. 20 M06-07: Fit the protective shell by pressing in the clips. Make sure that the sensors are fitted in place. 21 M06-07: Check that all clips are secured into the bumper shell. F930A642 21 20 21 20 19

39. 32 025 940 39 Saab 9-3 28 M08: Fit the wiring harness in the support for the bumper shell. 29 Fit the support to the bumper shell. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A659 28 29

40. 40 32 025 940 Saab 9-3 30 Lift up the bumper shell and thread the wiring harness through the hole under the left-hand rear lamp cluster. Fit the grommet. 31 Fit in the two tabs of the bumper shell under the holders and the outer corners between the wing liner and the mounting points at the wheel hous- ings. Press the bumper shell into place. 32 Connect the wiring harness for the bumper to the kit's wiring harness. Fit the connector into the hole beside the left-hand rear lamp cluster. Fasten the wiring harness for the distance sen- sors with a cable tie. 33 M04-07: Fit the bolts for the bumper shell which are located under the rear lamp clusters. 34 Fit and connect the rear lamp clusters. Check the fit against the boot lid moulding. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A660 33 34 31 34 30 32

5. 32 025 940 5 Saab 9-3 11 M03-07: Remove the bolts for the bumper shell which are located under the rear lamp clusters. 12 Remove the bumper bolts at the wheel hous- ings. 13 M08: Release the bumper's upper mounting by the rear lamp clusters. 14 Remove the bumper shell by pulling the sides outwards and then pulling the bu mper shell rear- wards. Important Place the bumper on a soft, clean surface. F930A629 11 14 12 13

10. 10 32 025 940 Saab 9-3 31 M08: Fit the wiring harness in the support for the bumper shell. 32 M08: Fit the support to the bumper shell. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A634 31 32

11. 32 025 940 11 Saab 9-3 33 Lift up the bumper shell and thread the wiring harness through the hole under the left-hand rear lamp cluster. Fit the grommet. 34 Fit in the two tabs of the bumper shell under the holders and the outer corners between the wing liner and the mounting points at the wheel hous- ings. Press the bumper shell into place. 35 Connect the wiring harness for the bumper to the kit's wiring harness. Fit the connector into the hole beside the left-hand rear lamp cluster. Fasten the wiring harness for the distance sen- sors with a cable tie. 36 M03-07: Fit the bolts for the bumper shell which are located under the rear lamp clusters. 37 Fit and connect the rear lamp clusters. Check the fit against the boot lid moulding. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A051 37 37 37 34 34 35 33 F930A635 35

12. 12 32 025 940 Saab 9-3 38 Fit the console in which such equipment as a CD changer/amplifier may be fitted. Plug in the connections to any equipment in the console. 39 Fit the side trims. 40 M03-07: Fit the side scuff plates. 41 Fit the panels and the clips in the luggage com- partment's side trims. 42 M03-07: Fit the scuff plate and lower the lug- gage compartment floor. WARNING Certain cars: The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connect or at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A636 42 39 39 40 41 42 42

19. 32 025 940 19 Saab 9-3 13 M08: Fit the wiring harness in the support for the bumper shell. 14 M08: Fit the support to the bumper shell. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A640 13 14

34. 34 32 025 940 Saab 9-3 9 Remove the rear lamp clusters. 10 M04-07: Remove the bolts for the bumper shell which are located under the rear lamp clusters. 11 M08: Insert a screwdriver into the hole to gain access under the catch for the bumper shell. Bend the screwdriver up to release the catch. 12 Remove the bumper shell by pulling the sides outwards and then pulling the bu mper shell rear- wards. Important Place the bumper on a soft, clean surface. F930A655 9 11 10 10

13. 32 025 940 13 Saab 9-3 43 Raise the car. 44 Fit the bumper bolts at the wheel housings. 45 Fit the two nuts holding the rear bumper air shield against the body. 46 Lower the car. 47 Close the boot lid. 48 Check the fit of the bumper. Adjust as neces- sary. 49 Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 50 With the ignition key in the ON position and reverse gear engaged, check that the system warns against objects in the rear by using tones. The first tone is given when an object is at a dis- tance of 1.8 metres. The signal then has a fre- quency of 2 tones per second, but the number of tones per second increases the closer the object becomes to the vehicle and changes as follows:  1.8 - 1.3 m: 2 tones/second  1.3 - 0.9 m: 3 tones/second  0.9 - 0.3 m: from 5 to 12 tones/second in close stages  0.3 m: continuous tone Note The diagnostic tool will, on some occasions, need to retrieve a security code in TIS. Information on what to do will be displaye d on the diagnostic tool display. F930A637 45 45 44 44

42. 42 32 025 940 Saab 9-3 39 Raise the car. 40 Fit the bumper bolts at the wheel housings. 41 Fit the two nuts holding the rear bumper air shield against the body. 42 Lower the car. 43 Close the boot lid. 44 Check the fit of the bumper. Adjust as neces- sary. 45 Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 46 With the ignition key in the ON position and reverse gear engaged, check that the system warns against objects in the rear by using tones. The first tone is given when an object is at a dis- tance of 1.8 metres. The signal then has a fre- quency of 2 tones per second, but the number of tones per second increases the closer the object becomes to the vehicle and changes as follows:  1.8 - 1.3 m: 2 tones/second  1.3 - 0.9 m: 3 tones/second  0.9 - 0.3 m: from 5 to 12 tones/second in close stages  0.3 m: continuous tone Note The diagnostic tool will, on some occasions, need to retrieve a security code in TIS. Information on what to do will be displaye d on the diagnostic tool display. F930A662 41 40 40 41

20. 20 32 025 940 Saab 9-3 15 M06-07: Fit the seals on the sensors. 16 M06-07: Fit the distance sensors and holders together. 17 M06-07: Fit the distance sensors into the bumper shell. 18 M06-07: Connect the kit's wiring harness to the sensors and route it along the shell. The con- nector should appear out towards the left-hand lamp cluster. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A641 15 16 18 18 18 17 17 17 17

30. 30 32 025 940 Saab 9-3 55 Lift the bumper shell and thread in the wiring harness. Fit the rubber grommet. 56 Guide the bumper shell's tabs in under the hold- ers. 57 Position the bumper shell's front corner between the wing liner and holder. Make sure that the shell lug is between the wing liner and the holder for the bumper shell. 58 Fit the screws at the wing liners. 59 Plug in the connector to the kit's wiring harness. Position under the rear fuse box. 60 Check that the rubber grommet is fitted cor- rectly. 61 Raise the car. 62 Fit the spoiler's centre nuts. 63 Lower the car and check the fit of the bumper shell. Adjust as necessary. 64 Close the tailgate. 65 Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 66 With the ignition key in the ON position and reverse gear engaged, check that the system warns against objects in the rear by using tones. The first tone is given when an object is at a dis- tance of 1.8 metres. The signal then has a fre- quency of 2 tones per second, but the number of tones per second increases the closer the object becomes to the vehicle and changes as follows:  1.8 - 1.3 m: 2 tones/second  1.3 - 0.9 m: 3 tones/second  0.9 - 0.3 m: from 5 to 12 tones/second in close stages  0.3 m: continuous tone WARNING The wiring harness must be routed and secured so that it cannot become trapped or chafe against anything when refitting dismantled parts. Incorrect routing could cause damage to the wiring harness and short circuit/fire. F930A651 56 58 58 55 62 62 59 Note The diagnostic tool will, on some occasions, need to retrieve a security code in TIS. Information on what to do will be displaye d on the diagnostic tool display.

37. 32 025 940 37 Saab 9-3 21 Remove the support from the bumper shell. 22 M04-07: Align the bumper shell's decor strip using the guide tab and press in the hooks start- ing in the centre and then continuing out to the sides. 23 M04-07: Fit the seals on the sensors. 24 M04-07: Fit the distance sensors and holders together. 25 M04-07: Fit the distance sensors into the decor strip mountings. 26 M04-07: Fit the wiring harness for the sensors in the bumper shell groove. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. F930A658 23 24 25 21 26 26 26

8. 8 32 025 940 Saab 9-3 23 Remove the support from the bumper shell. 24 M03-07: Align the bumper shell's decor strip using the guide tab and press in the hooks start- ing in the centre and then continuing out to the sides. 25 M03-07: Fit the seals on the sensors. 26 M03-07: Fit the distance sensors and holders together. 27 M03-07: Fit the distance sensors into the decor strip mountings. 28 M03-07: Fit the wiring harness for the sensors in the bumper shell groove. 29 M03-07: Fit the support to the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. F930A632 25 26 27 23,29 28 28 28

2. 2 32 025 940 Saab 9-3 4D 1 SPA control module 2 M03-07: Holder (x4) 3 M03-07: Seal (x4) 4 M03-07: Distance sensor (x4) 5 M03-07: Decor strip, bumper 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Dust cover 9 Cable tie (x8) 10 M08: Ta p e The following parts must be ordered separately M08: Hole-punching tool M08: Distance sensor (x4) M08: Holder (x4) F930A626 1 9 5 7 6 2 3 4 8 10

14. 14 32 025 940 Saab 9-3 5D 1 SPA control module 2 M06-07: Holder (x4) 3 M06-07: Seal (x4) 4 M06-07: Distance sensor (x4) 5 M06-07: Protective shell, bumper 6 Wiring harness, distance sensor 7 Wiring harness, rear harness 8 Cable tie (x8) 9Bracket 10 M08: Ta p e The following parts must be ordered separately M08: Hole-punching tool M08: Distance sensor (x4) M08: Holder (x4) F930A639 1 5 7 6 2 3 4 8 9 10

31. 32 025 940 31 Saab 9-3 CV 1 SPA control module 2 M04-07: Holder (x4) 3 M04-07: Seal (x4) 4 M04-07: Distance sensor (x4) 5 M04-07: Decor strip, bumper 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Cable tie (x8) 9 M08: Ta p e The following parts must be ordered separately M08: Hole-punching tool M08: Distance sensor (x4) M08: Holder (x4) F930A652 1 8 5 7 6 2 3 4 9

Weergaven

  • 686 Totale weergaven
  • 559 Websiteweergaven
  • 127 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 30 www.saabpartners.com
  • 6 52.29.207.161
  • 14 saabpartners.com
  • 5 54.154.214.138