Parking assistance (SPA) 9-3 5D

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

2. 2 32 025 604 Saab 9-3 5D M06- 1 SPA control module 2 Holder (x4) 3Seal (x4) 4 Distance sensor (x4) 5 Protective shell, bumper 6 Wiring harness, distance sensor 7 Wiring harness, rear harness 8 Cable tie (x4) F930A404 1 5 7 6 2 3 4 8

3. 32 025 604 3 Saab 9-3 5D M06- 1 Turn the ignition key to the OFF position and remove the key. 2 Raise the car. 3 Remove the spoiler's centre nuts. 4 Remove the screws to the wheel housing. 5 Lower the car and open the tailgate. 6 Insert a screwdriver in the hole to reach under the catch for the bumper shell. Bend up using the screwdriver to release the catch. F930A405 3 3 6 4 4

5. 32 025 604 5 Saab 9-3 5D M06- 10 Pull the cellular block from the bumper shell lugs. 11 Remove the protective corner mouldings and the protective shell by inserting tool 82 93 474 under the shell to release the clips. F930A407 11 10 11 11 11

7. 32 025 604 7 Saab 9-3 5D M06- 16 Fit the cellular block by guiding it in toward the bumper shell lugs. Press the cellular block in. 17 Fit the protective shell by pressing in the clips. Make sure that the sensors are located correctly. 18 Check that all the clips are secured in the bumper shell. F930A409 18 17 17 18 16

8. 8 32 025 604 Saab 9-3 5D M06- 19 Fold down the rear seat backrests. 20 Remove the left and right-hand C-pillar trim. Use 82 93 474 Removal tool to remove the cover plate. 21 Remove the left and right-hand side bolsters. Use 82 93 474 Removal tool to remove the clips. F930A410 20 20 20 21 21 21

14. 14 32 025 604 Saab 9-3 5D M06- 49 Fit the left and right-hand side bolsters. Check that the belt is not twisted. 50 Fit the left and right-hand C-pillar trim. 51 Fold up the backrests. F930A416 50 50 50 49 49 49

4. 4 32 025 604 Saab 9-3 5D M06- 7 Pull the bumper shell away from the holders. 8 Release the catches using a screwdriver. Detach the shell from the moulding. 9 Lift off the bumper shell. Important Place the bumper on a soft, clean surface. F930A406 8 9 7

6. 6 32 025 604 Saab 9-3 5D M06- 12 Fit the seals to the sensors. 13 Fit together the distance sensors and the holders. 14 Fit the distance sensors in the bumper shell. Turn the connector in the right direction, see illustration. 15 Connect the kit's wiring harness to the sensors and pull it along the shell. The connector must come out toward the left-hand light cluster. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. F930A408 12 13 15 15 15 14 14 14 14

9. 32 025 604 9 Saab 9-3 5D M06- 22 Remove the luggage compartment floor. 23 Cars with subwoofer: Lift up the subwoofer. 24 Remove the scuff plate's clips using 84 71 179 Removal tool, clips and lift up the scuff plate. F930A411 24 24 22 22

13. 32 025 604 13 Saab 9-3 5D M06- 46 Fit the scuff plate. 47 Cars with subwoofer: Lower the subwoofer and screw it in. 48 Fit the luggage compartment floor. F930A415 46 46 48 48

1. Saab 9-3 5D M06- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 5D M06- Parking assistance (SPA) Accessories Part No. Group Date Instruction Part No. Replaces 32 025 603 9:40-05 Sep 05 32 025 604 F930A403

10. 10 32 025 604 Saab 9-3 5D M06- 25 Steps 25-33 must be carried out on both the left and right-hand sides. Remove the clip from the mounting in the body. Use a screwdriver. 26 Remove the two-stage rivet using 84 71 179 Removal tool, clips. 27 Remove the mounting for the cargo guard (if fitted). 28 Remove the cover and the screw. 29 Lift the cover away from over the storage compartment. 30 Remove the luggage compartment lighting lens and insert the bulb holder through the hole in the side trim. 31 Right-hand side: Also unplug the connector to the 12 V socket. 32 Remove the trim so that the clips release. 33 Remove the clip for the foam block and remove the foam block. F930A412 31 28 28 30 29 33 25 27 26

12. 12 32 025 604 Saab 9-3 5D M06- 37 Steps 37-45 must be carried out on both the left and right-hand sides. Fit the foam block and its clips. 38 Fit the luggage compartment lighting. Right-hand side: Also plug in the connector to the 12 V socket. 39 Press the side trim into its clips. 40 Fit the cover over the storage compartment. 41 Fit the screw. 42 Fit the cover. 43 Fit the mounting for the cargo guard (if fitted). 44 Fit the two-stage rivet. 45 Fit the clip to the mounting in the body. F930A414 40 38 45 44 43 42 41 38 37

11. 32 025 604 11 Saab 9-3 5D M06- 34 Remove the connector for the rear harness (blue and grey) from the electrical centre. 35 Remove the car's rear harness and fit the wiring harness from the kit instead. Plug the connec- tors to the electrical centre last of all. 36 Fit the kit's control module on the bracket by the electrical centre and plug in the connectors. WARNING The wiring harness must be routed and secured so that it cannot become trapped or chafe against anything when refitting dismantled parts. Incorrect routing could cause damage to the wiring harness and short circuit/fire. Note The wiring harness from the kit is produced for cars with max. equipment which is why not all connectors can be plugged in for all cars. Tape up unused connectors so that they cannot fall and rattle. F930A413 35 36 34

15. 32 025 604 15 Saab 9-3 5D M06- 52 Lift the bumper shell and thread in the wiring harness. Fit the rubber grommet. 53 Guide the bumper shell's tabs in under the holders. 54 Position the bumper shell's front corner between the wing liner and holder. Make sure that the shell lug is between the wing liner and the holder for the bumper shell. 55 Fit the screws at the wing liners. 56 Plug the connector to the connector under the REC. 57 Check that the rubber grommet is fitted correctly. 58 Raise the car. 59 Fit the spoiler's centre nuts. 60 Lower the car and check the fit of the bumper shell. Adjust as necessary. 61 Close the tailgate. 62 Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 63 Turn the ignition key to the “ON” position and check all functions affected by the change of wiring harness (light clusters, luggage compart- ment locking, rear wiper etc.). 64 With the ignition key in the ON position and reverse gear engaged, check that the system warns against objects in the rear by using tones. The first tone is given when an object is at a dis- tance of 1.8 metres. The signal then has a fre- quency of 2 tones per second, but the number of tones per second increases the closer the object becomes to the vehicle and changes as follows: · 1.8 - 1.3 m: 2 tones/second · 1.3 - 0.9 m: 3 tones/second · 0.9 - 0.3 m: from 5 to 12 tones/second in close stages · 0.3 m: continuous tone WARNING The wiring harness must be routed and secured so that it cannot become trapped or chafe against anything when refitting dismantled parts. Incorrect routing could cause damage to the wiring harness and short circuit/fire. F930A417 56 59 59 52 55 55 53

Weergaven

  • 612 Totale weergaven
  • 517 Websiteweergaven
  • 95 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 3

  • 18 www.saabpartners.com
  • 2 52.29.207.161
  • 4 54.154.214.138