Rear hitch wiring harness, manoeuvre 900, 9-3

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

4. 4 52 46 095 Saab 900 M94-M98, Saab 9-3 9-3 16 Unplug the blue 33-pin connector. 17 Undo the two nuts securing the connector bracket and fold up the bracket. 18 Connect the VIOLET cable from the kit to pin 7 in the blue connector on the connector bracket. 19 Screw on the connector bracket and plug in the 33-pin connector. D930A116 16 17 17

5. 52 46 095 5 Saab 900 M94-M98, Saab 9-3 RHD 20 Cut the BLUE/WHITE cable at the 2-pin connec- tor. 21 Fit the cable for RHD cars, kit 400 101 663, to the connector and run the lead over to the right- hand side of the dashboard. 22 Make sure to secure the cable so that is does not come into contact with any moving parts. D930A117 20 21 22

2. 2 52 46 095 Saab 900 M94-M98, Saab 9-3 Initial conditions: Rear sill plate removed. Left-hand rear side trim removed. Rear hitch with wiring harness fitted. 1 Press the 8-pin connector onto the rear hitch wiring harness. 2 Unplug the connectors to the rear lamp clusters. 3 Plug the connector from the fitting kit with the part number sleeve to the left-hand rear light and the other connector from the same cable branching to the right-hand rear light. 4 Unplug the black 4-pin connector behind the left-hand wheel housing in the luggage compart- ment and plug in the other 4-pin connectors from the manoeuvre kit. D930A114 3 3 1 4 2

7. 52 46 095 7 Saab 900 M94-M98, Saab 9-3 Wiring diagram The fitting kit is indicated inside the dashed rectan- gle on the wiring diagram. The arrows show where the wiring harness connectors are connected. 1.0 BK/GN 1.0 BU/BN BU/BN 1.0 WH/RD 1.0 BN/BU 1.0 GN/WH 1.0 GY/BK 1.0 BU/WH 1 1234 1 H2 2 H3 2 400 101 663 1 2 3 4 4 3 2 1 4321 900 BK 1.0 OG/BU 1.0 GY/BK 1.0 1.0 GN/YE BN/GN 1.0 BK 1.0 1.0 YE/WH BU/WH 1.0 RHD GN/WH 1.0 WH/RD 1.0 RHD 1.0 BU/WH LHD 7 VT 1 2 3 4 33 32 15 BU/WH H4-3 1 2 3 4 BK/GN 1.0 1 H1 27RL 27RR YE/GN 1.0 258 3 4 2 5 7 8 6 1 LHD RHD BU/WH 1.0 9-3 1 H2 2 VT 1.0 30 M8679300 990614 Pos.nr Name 15 Number plate lighting 27RL Left rear direction indicator 27RR Right rear direction indicator 32 Reversing lights 33 Rear fog lights 258 Connector for rear hitch wiring harness H1 1-pin connector H2 2-pin connector H3 2-pin connector in RHD kit H4-3 Black 4-pin connector behind left-hand wheel housing

6. 6 52 46 095 Saab 900 M94-M98, Saab 9-3 LHD+RHD 23 Remove fuse 30 for the rear lights in the fuse holder on the side of the dashboard. 24 Disconnect the blue/white cable terminal. 25 Connect the blue/white cable in the kit. 26 Fit the disconnected cable terminal to pos. 1 in the kit’s 2-pin connector. 27 Plug together the connectors. 28 Replace the fuse. 29 Check the function. 30 Replace all the disassembled parts. 30 D930A118 24 23 27 25 26

1. 52 46 095 1 Saab 900 M94-M98, Saab 9-3 900, 9-3 MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTALLATIONS DE MONTAGE Saab 900 M94-M98, Saab 9-3 Rear hitch wiring harness, manoeuvre 1 Wiring harness 2 1-pin connector (x2) 3 2-pin connector 4 Cable terminal (x2) 5 Cable tie (x5) RHD also requires kit 400 101 663 Accessories Part No. Group Date Instruction Part No. Replaces 400 112 090 9:37-1 Jun 99 52 46 095 75 04 06 Oct 95 86 79 300 D930A113 3 4 5 2 5 1

3. 52 46 095 3 Saab 900 M94-M98, Saab 9-3 5 Remove the left-hand sill plates and cover under the steering wheel. RHD: Remove the glove compartment. 6 3D: Remove the left-hand side trim on the rear seat. 7 Lay the wiring harness along the left-hand side of the car, from the luggage compartment to the dashboard. 8 Fold away the carpet from the connectors on the bracket below the A-pillar. Proceed to step 16 for the Saab 9-3. 900 9 Cut off the VIOLET cable on pin 13 in the grey 33-pin connector as close as possible to the connector. 10 Strip about 15 mm and fit the cable sleeve from the kit onto the cable. 11 Fit the cable sleeve into the 1-pin sleeve con- nector. 12 Cut off the cable terminal on the kit’s VIOLET cable. 13 Strip about 15 mm and fit the pin from the kit onto the cable. 14 Fit the pin into the 1-pin connector from the kit. 15 Press together the connectors. Proceed to step 20 for RHD cars or to step 23 for others. D930A115 9 11 10 12 5 7

Weergaven

  • 675 Totale weergaven
  • 563 Websiteweergaven
  • 112 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 12 www.saabpartners.com
  • 19 saabpartners.com
  • 1 52.29.207.161
  • 3 54.154.214.138