Rear spoiler 900 3D/5D, 9-3 3D/5D

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

1. Thhi("9$9H(#Thhi(""9$9 9-3 Monteringsanvisning SCdefault HPIU@SDIBT6IWDTIDIB  DITU6GG6UDPIDITUSV8UDPIT HPIU6B@6IG@DUVIB  DITUSV8UDPIT9@HPIU6B@ SITdefault Thhi("9$9H(#Thhi(""9$9 Srh…†ƒ‚vyr… 1 Spoiler 2 Washer, round with tape (x2) 3 Six-sided nut with washer (x4) 4 Zinc washer (x4) 5 Sealing tape (3 parts) 6 Drill pattern (2 parts) 7 Gas strut (x2) Accessories Part No. Group Date Instruction Part No. Replaces # ( " ()'## Pp‡ #&'%#%" #&'%#%"6ˆt(' D980A324 3 2 5 1 4 6 5 7

2. 2 47 86 463 Thhi("9$9H(#Thhi(""9$9 The spoiler is treated with black primer and conse- quently prepared for painting. 1 Paint the spoiler the same colour as the car. See “Painting instructions for pre-primed PUR-RIM plastic“ in these mounting instructions. 2 8h…†v‡u…rh…vq‚vƒr…†) Remove wiper arm 3 Open the hatchback. 4 Remove the trim on the inside of the hatch. 5 8h…†v‡u‚ˆ‡…rh…vq‚vƒr…† : Place a piece of tape above the high level brake light, measure to determine the centre of the brake light and mark accordingly on the tape. 8h…†v‡u…rh…vq‚vƒr…†) Remove wiper motor in the following manner: • Unplug the wiper connector. • Remove the screws that hold the wiper motor. • Lift away the wiper motor, retaining the rubber grommet with the motor. 6 Complete the pattern by: • Cut out the first part of the pattern as shown by scissors number 1. • Tape the two parts together. Use the lines to insure proper alignment. • Cut the pattern out as shown by scissors number 2. 7 8h…†v‡u‚ˆ‡…rh…vq‚vƒr…) Place the pattern on the boot lid so that the bottom edge rests against the rear window rubber seal and the upper edge touches the high mounted stop- light. Make sure that the centre mark on the pattern matches the measured centre mark of the boot lid. Secure the pattern with tape. 8h…†v‡u…rh…vq‚vƒr…†) Place the pat- tern against the edge of the rear window wiper motor hole and against the rear window's rubber seal. Secure the pattern with tape. 8 Check that the distance between the hole mark- ings matches the spoiler stud placement. 9 Mark the position of the holes, using a centre punch. 10 Drill an 8 mm hole according to the markings. Start with a smaller bit. 11 Protect the holes from corrosion as follows: • Deburr the holes and remove loose drillings and flakes of paint with compressed air. • Apply Standox 1K Primer Filler or other equivalent product. • Apply finish paint. • Affix zinc tape over the holes and press down with a screwdriver so that the tape folds down over the edges. D980A325 5 5 2 5 6,7 5 5 I‚‡r Exercise care.

3. 47 86 463 3 Thhi("9$9H(#Thhi(""9$9 12 Mount the sealing tape on the spoiler and fit the spoiler on the boot lid. 13 Attach the washers with the tape side against the boot lid and the nuts that hold the spoiler. Uvtu‡rvt‡‚…„ˆr%I€#$yiss‡ 14 8h…†v‡u…rh…vq‚vƒr…†) Attach the wiper motor as follows: • Refit the wiper motor along with the rubber grommet. • Attach the screws that hold the wiper motor. • Reconnect the wiper motor wiring. 15 Reattach the upholstery on the inside of the boot lid. 16 Replace the gas struts as follows: – Remove the locking clips at both ends of the gas struts. Use a standard screwdriver. – Pull the gas struts loose from their attachment points on the boot lid and chassis. – Attach the gas struts from the kit. 17 Close the boot lid. 18 8h…†v‡u…rh…vq‚vƒr…†) Attach the wiper arm. Qhv‡vtqv…rp‡v‚†s‚…ƒ…v€rqQVSSDHƒyh†‡vp • During the painting process the spoiler should be placed in such a way that it will not be deformed. • The temperature must not exceed +40 ° C (104 ° F). • The spoiler is preprimed as delivered from the supplier. • Clean gloves should be worn when handling the spoiler. 9…’vt‡v€r 70 minutes at +40 ° C (104 ° F) Q…rƒh…h‡v‚ • For best results, apply pore filler first. • Sand the primed surfaces thoroughly. Use 3M 1200 or 800 abrasive paper. X6SIDIB The boot lid must be supported while the gas struts are removed. D980A326 12 13 13 12 16 16

Weergaven

  • 671 Totale weergaven
  • 560 Websiteweergaven
  • 111 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 3

  • 11 www.saabpartners.com
  • 13 saabpartners.com
  • 2 54.154.214.138