Sill covers 9-3

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

2. 2 12 798 025 Saab 9-3 M03- 1 Sill cover L 2 Sill cover R 3 Screw with washer (x6) 4 Bolt (x12) 5 Plastic rivet (x12) 6 Clip nut (x6) 7 Stone chip protection tape, right (R) and left (L) 1 2 7 3 4 6 5 R L F980A057

4. 4 12 798 025 Saab 9-3 M03- 8 Remove the plastic clip from the old sill cover and fit it in the same position on the new one. Fit the clip nuts to the front and rear ends of the sill covers. 9 Affix the stone chip protection tape in the follow- ing way: – Clean the surface on which the stone chip protection tape is to be affixed. – Brush the area on which the stone chip pro- tection tape is to be affixed with soapy water. – Separate the stone chip protection tape from the backing and place the tape on the sill cover. – Position the stone chip protection tape at the bottom, bend the tape upwards and start pressing out the soapy water at the top of the stone chip protection tape. Press out the air and soapy water at the bottom so that the stone chip protection tape adheres. F980A059 8 8 8 9

5. 12 798 025 5 Saab 9-3 M03- 10 Pull out the rear edge of the plastic wheel hous- ing slightly, hook the new sill cover into the front wing and press in the clip at the rear door. 11 Fit the screws behind the rubber moulding. 12 Press the rubber moulding into place and press its lip into the groove in the rear edge of the sill cover by stretching the rubber moulding slightly forward, inserting the lip into the groove and moving the rubber moulding back. 13 Fit the sill cover screws at the wheel housings. 14 Fit the plastic rivets and tap in the centre pin. Check the fit of the sill cover. 15 Repeat steps 2-14 on the right-hand side of the car. 16 Lower the car. F980A060 13 13 11 11 11 12 10 14 14 14

3. 12 798 025 3 Saab 9-3 M03- The sill covers have been treated with grey primer and are ready for painting. 1 Paint the sill covers the same colour as the body; see “Directions for painting preprimed PP/ EPDM plastic“ in these installation instructions. 2 Raise the car. 3 Remove the screws at the wheel housings on the left-hand side of the car. 4 Remove the rubber moulding from the old sill cover, but not from the front wing. 5 Remove the screws of the old sill cover behind the rubber moulding. 6 Remove the plastic rivets by pressing in the cen- tre pin. 7 Remove the sill guard by loosening the rear edge and pressing it forward so it releases from the front wing. Gather the clip centre pins. Important Do not pull off the rubber moulding from the front wing as the wing liner must then be removed so that the rubber moulding can be refitted. F980A058 3 3 5 5 4 5 6 6 7 6

1. Saab 9-3 M03- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 M03- Sill covers Accessories Part No. Group Date Instruction Part No. Replaces 12 787 094 9:84-16 Sep 02 12 798 025 12 798 025 Mar 02 F980A056

6. 6 12 798 025 Saab 9-3 M03- Directions for painting preprimed PP/ EPDM plastic  Place the sill covers in such a way as they will not be distorted while painting.  The temperature must not exceed +40°C (104°F).  The sill covers are primed on delivery.  Use clean gloves when handling the sill covers. Drying times 70 minutes at 40°C (104°F). Preparations  Smooth off the primed surface thoroughly. Use abrasive paper 3M 1200 or 800.

Weergaven

  • 383 Totale weergaven
  • 329 Websiteweergaven
  • 54 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 3

  • 5 www.saabpartners.com
  • 2 52.29.207.161
  • 4 saabpartners.com