Sill covers 9-3 CV

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

2. 2 12 805 381 Saab 9-3 CV M04- 1 Sill cover L 2 Sill cover R 3 Screw with washer (x6) 4 Bolt (x10) 5 Plastic rivet (x16) 6 Clip nut (x6) F980A253 3 4 5 2 1 6

3. 12 805 381 3 Saab 9-3 CV M04- The sill covers have been treated with grey primer and are ready for painting. 1 Paint the sill covers the same colour as the body; see “Directions for painting preprimed PP/ EPDM plastic” in these installation instructions. 2 Open the doors and raise the car. 3 Remove the screws at the wheel housings on the left-hand side of the car. 4 Remove the scuff plate rubber moulding from the scuff plate, but only far enough for the five screws to be visible. 5 Remove the scuff plate screws behind the rubber moulding. 6 Remove the plastic rivets by pressing in the centre pin. 7 Remove the scuff plate by loosening the rear edge and pressing it forward so it releases from the front wing. Gather the clip centre pins. F980A254 6 6 3 7 4 5 5 3

4. 4 12 805 381 Saab 9-3 CV M04- 8 Fit the clip nuts in the front and rear edges of the sill covers. F980A255 8 8

1. Saab 9-3 CV M04- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 CV M04- Sill covers Accessories Part No. Group Date Instruction Part No. Replaces 12 805 377 9:84-31 Sep 03 12 805 381 F980A252

5. 12 805 381 5 Saab 9-3 CV M04- 9 Pull out the front plastic wheel housing slightly at the rear edge, hook the sill cover securely into the front wing and press the sill cover securely at the back. 10 Fit the screws in the sill. 11 Press the rubber moulding securely onto the sill cover. 12 Fit the sill cover screws at the wheel housings. 13 Fit the plastic rivets and tap in the centre pins. Check the fit of the sill cover. 14 Repeat steps 3-14 on the right-hand side of the car. 15 Lower the car. Important The front edge of the rear plastic wheel housing must be bent out slightly. F890A256 9 F980A256 10 10 11 9 12 12 13 13 13

6. 6 12 805 381 Saab 9-3 CV M04- Directions for painting preprimed PP/ EPDM plastic • Place the sill covers in such a way as they will not be distorted while painting. • The temperature must not exceed +40 °C (104 °F). • The sill covers are primed on delivery. • Use clean gloves when handling the sill covers. Drying times 70 minutes at 40 °C (104 °F). Preparations • Smooth off the primed surface thoroughly. Use abrasive paper 3M 1200 or 800.

Weergaven

  • 539 Totale weergaven
  • 444 Websiteweergaven
  • 95 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 5

  • 16 www.saabpartners.com
  • 11 52.29.207.161
  • 5 saabpartners.com
  • 1 52.211.236.180
  • 4 54.154.214.138