Towbar 9-3 4D/CV 1

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

18. 18 32 026 048 Saab 9-3 4D/CV M03-

13. 32 026 048 13 Saab 9-3 4D/CV M03- Wiring diagram BK 4. 0 G31- 5 26 10 258 13 10 11 7 3 R- B 2 G3 DIODE BOX PK 1. 0 C1 -5 GY 1. 0 C1 -6 OG 1. 0 C1 -4 GN /B U1 .0 C1 -9 BK 2. 5 C3 1 GN 1. 0 C1 -1 YE 1. 0 C1 -2 BN 1. 0 C1 -3 WH 1. 0 C 31- 1 I- BU S +3 0 +3 0 26 25 23 24 18 11 9 22 3 21 2 5 20 16 15 12 6 17 14 19 731 13 27/30R 27/30L SAE J 1239 701 FL12US 021217 1 23 4 13 4 10 1 8 7

17. 32 026 048 17 Saab 9-3 4D/CV M03- Template 1 F980A514 1 140mm 12mm

19. 32 026 048 19 Saab 9-3 4D/CV M03- Template 2 F980A515 2 140mm 103mm

14. 14 32 026 048 Saab 9-3 4D/CV M03- List of components No. Name position Components 13 Lamp, parking light, trailer 27/30 Lamp, direction indicators/brake lights, trailer 258 Connector, towbar wiring harness, in the luggage compartment electrical distri- bution unit 701 Luggage compartment electrical distribution unit, on the wall behind the left-hand rear wheel housing 731 Trailer control module, in the luggage compartment electrical distri- bution unit Grounding points G3 In the luggage compartment below the left- hand light cluster

2. 2 32 026 048 Saab 9-3 4D/CV M03- 1 Body bracket 2 Ball mounting 3 Locking pin 4 Bolt (x4) 5 Screw (x2) 6 Nut (x4) 7 Reinforcement plate (x2) 8 Ball cap 9 Storage bag 10 Key (x2) 11 Wiring harness with diode box 12 Cable tie (x4) 13 Electronic module 14 Cover (purchased separately) 15 Ball 16 Spring washer 17 Nut F980A034 12 16 15 17 14 10 11 14 13 5 2 3 9 1 8 7 7 6 4

6. 6 32 026 048 Saab 9-3 4D/CV M03- 13 Mount the towing bracket using bolts and nuts together with the reinforcements in the four bumper member holes and raise the car. 14 Fasten the towing bracket in the floor under the spare wheel well. 15 Tighten the bumper member mountings against the body as well as the screws, bolts and nuts holding the towing bracket against the bumper member and floor. Tightening torque, bumper member against body 50 Nm (37 lbf ft) Tightening torque, towing bracket against bumper member 50 Nm (37 lbf ft) Tightening torque, towing bracket against floor 50 Nm (37 lbf ft) F980A508 13,15 13,15 15 15 15 15 13 14,15 14,15

11. 32 026 048 11 Saab 9-3 4D/CV M03- 4D 28 Lower the car and run the wiring harness along the other wiring harnesses towards the left-hand side of the car and to the rear electrical distribu- tion. 29 Plug the wiring harness connector into the rear electrical distribution box and secure the wiring harness with 4 cable ties. 30 Fit the kit's electronic module in the rear electri- cal distribution box. 31 Fit the left-hand side trim. 32 Fit the side scuff plate on the left-hand side. 33 Fit the scuff plate. 34 Fit the hatches in the side trims of the luggage compartment. 35 Fit the ball mounting, see “User instructions”. 36 Fit the ball to the mounting. Tightening torque 180 Nm (133 lbf ft) 37 Check the fit of the bumper. Adjust as necessa- ry. 38 Carefully remove the page regarding fitting and removing the ball unit and give it to the customer together with the installation instructions. F980A538 29 29 29 29 36 30

12. 12 32 026 048 Saab 9-3 4D/CV M03- CV 39 Lower the car and run the wiring harness along the other wiring harnesses towards the left-hand side of the car and to the rear electrical distribu- tion. 40 Plug the wiring harness connector into the rear electrical distribution box and secure the wiring harness with 4 cable ties. 41 Fit the kit's electronic module in the rear electri- cal distribution box. 42 Fit the left-hand side trim. Connect the luggage compartment lighting and hook the strap on. 43 Fit the side scuff plate on the left-hand side. 44 Fit the scuff plate. 45 Fit the carpet on the luggage compartment floor. 46 Fit the ball mounting, see “User instructions”. 47 Fit the ball to the mounting. Tightening torque 180 Nm (133 lbf ft) 48 Check the fit of the bumper. Adjust as necessa- ry. 49 Carefully remove the page regarding fitting and removing the ball unit and give it to the customer together with the installation instructions. F980A539 40 40 47 40 40 41

5. 32 026 048 5 Saab 9-3 4D/CV M03- 8 Remove the rear lamp clusters. 9 SPA: Unplug the connector. 10 Remove the bumper shell bolts that are located below the rear lamp clusters. 11 Remove the bumper bolts at the wheel hous- ings. 12 Remove the bumper shell by pulling the sides outwards and then pulling the bu mper shell rear- wards. 8 8 8 10 12 11 8 F980A259 8 8 CV 4D 8

16. 16 32 026 048 Saab 9-3 4D/CV M03- To detach the towball unit 1 Turn the sleeve to access the lock. Insert the key, turn it clockwise and remove the pin's lock. 2 Pull out the pin. 3 Fit the lock on the pin, turn the key anticlockwise and remove it. 4 Remove the ball unit. 5 Fit the cover. When the towbar is not in use, the wiring harness must be stored in the following location: 4D: Behind the hatch in the left-hand side trim. CV: Beside the spare wheel in the spare wheel well. F980A136 4 3 1 1 3

1. Saab 9-3 4D/CV M03- 4900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 4D/CV M03- Towbar Accessories Part No. Group Date Instruction Part No. Replaces 12 804 703 32 026 048 9:86-04 Oct 07 12 797 883 Jun 07 F980A033

3. 32 026 048 3 Saab 9-3 4D/CV M03- The towing bracket was designed and tested in accordance with standard V-5 Class 2. Maximum permitted trailer weight: Trailer with brake: 3500 lbs (1587 kg) Trailer without brake: 1000 lbs (455 kg) Max. permissible ball pressure: 165 lbs (75 kg) Note Always check national legislation and regulations regarding mounting a towing bracket. Ensure that all requirements are complied with. Important The wiring harness must be connected following the description in these installation instructions. This is a requirement. If the wiring harness is con- nected in any other way, it could negatively affect the car's electrical system.

4. 4 32 026 048 Saab 9-3 4D/CV M03- 1 Raise the car. 2 Remove the two nuts holding the rear bumper air shield against the body and the two bolts holding the bumper shell against the wheel housings. 3 Lower the car and open the boot lid. CV: Remove the carpet on the luggage com- partment floor. 4 Remove the luggage compartment scuff plate. 5 4D: Remove the hatch in the luggage compart- ment left-hand side trim and lower the hatch on the right-hand side. 6 Remove the side scuff plate on the left-hand side. 7 Remove the clips for the left-hand side trim and fold the trim aside. CV: Unhook the strap on the rear side of the side trim and remove the connector from the luggage compartment lighting. Remove the side trim. 5 6 4 5 7 7 7 2 2 F980A022

10. 10 32 026 048 Saab 9-3 4D/CV M03- 20 Lower the car. 21 SPA: Insert and plug in the connector. 22 Fit the two tabs of the bumper shell under the holes and the outer corners between the wheel arch liner and the holder at the wheel housings. Press the bumper shell into place. 23 Fit the bumper shell bolts that are located below the rear lamp clusters. 24 Fit the bumper bolts at the wheel housings. 25 Fit and connect the rear lamp clusters. Check the fit against the boot lid moulding. 26 Raise the car. 27 Fit the two nuts holding the rear bumper air shield against the body and the two bolts hol- ding the bumper shell against the wheel hous- ings. 4D: Continue with step 28. CV: Continue with step 39. F980A537 23 23 22 22 27 22 27 27

8. 8 32 026 048 Saab 9-3 4D/CV M03- 18 M08, cars without bumper skirt: 18.1 Print out template 1 and cut out the tem- plate. 18.2 Position template 1 (A) on the inside of the bumper shell against the upper marking and draw around the lower edge of the template. 18.3 Cut/saw from the inside of the bumper shell (B). Important Check that the size of the template corresponds with the specified dimensions after printing it out. Create your own template if it is not possible to make the printout correspond with the specified dimensions. WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection equipment, such as pro- tective gloves, safety goggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper. 18 F980A535 A B

9. 32 026 048 9 Saab 9-3 4D/CV M03- 19 M08, cars with bumper skirt: 19.1 Print out template 2 and cut out the tem- plate. 19.2 Saw from the inside of the bumper in accordance with the outer markings up to (A). 19.3 Turn the bumper over. 19.4 Position template 2 (B) on the outside of the bumper skirt against the edge (C). Cen- tre between the sawn grooves and draw around the template. 19.5 Saw from the outside of the bumper skirt in accordance with the marking (D). Important Check that the size of the template corresponds with the specified dimensions after printing it out. Create your own template if it is not possible to make the printout correspond with the specified dimensions. 19 F980A536 B A A D C WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection eq uipment, such as pro- tective gloves, safety g oggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper.

7. 32 026 048 7 Saab 9-3 4D/CV M03- 16 M03-07, cars without bumper skirt Cut/saw from the inside of the bumper, inside the reinforcement ribs in accordance with the marking (A). 17 M03-07, cars with bumper skirt Cut/saw from the inside of the bumper, inside the reinforcement ribs in accordance with the marking (B). WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection equipment, such as pro- tective gloves, safety goggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper. 17 16 F980A534 B A WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection eq uipment, such as pro- tective gloves, safety g oggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper.

15. 32 026 048 15 Saab 9-3 4D/CV M03- User instructions (keep in the car's Owner's Manual) To attach the towball unit 1 Remove the cover. 2 Fit the ball unit. 3 Insert the key in the pin's lock, turn it clockwise and remove the pin's lock. 4 Insert the pin into the towing bracket hole and fit the lock to the pin. Turn the key anticlockwise to lock the pin and then remove the key. Turn the lock sleeve to hide and protect the lock. WARNING To ensure that the towbar is coupled correctly and safely : WARNING • The coupling mechanism must always be kept well lubricated. Contact your nearest Saab dealer regarding a suitable grease. WARNING • Always fit the protective cover when the tow- ball unit is not attached. WARNING • It must always be possible to detach and attach the towball un it without it jamming. F980A038 2 3 4 4

Weergaven

  • 680 Totale weergaven
  • 572 Websiteweergaven
  • 108 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 5 52.29.207.161
  • 11 www.saabpartners.com
  • 10 saabpartners.com
  • 5 54.154.214.138