Towbar 9-3 5D

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

16. 16 12 795 100 Saab 9-3 5D M06-

20. 20 12 795 100 Saab 9-3 5D M06-

22. 22 12 795 100 Saab 9-3 5D M06-

14. 14 12 795 100 Saab 9-3 5D M06- Wiring diagram BK 4. 0 G31- 5 26 10 258 13 10 11 7 3 R- B 2 G3 DIODE BOX PK 1. 0 C1 -5 GY 1. 0 C1 -6 OG 1. 0 C1 -4 GN /B U1 .0 C1 -9 BK 2. 5 C3 1 GN 1. 0 C1 -1 YE 1. 0 C1 -2 BN 1. 0 C1 -3 WH 1. 0 C 31- 1 I- BU S +3 0 +3 0 26 25 23 24 18 11 9 22 3 21 2 5 20 16 15 12 6 17 14 19 731 13 27/30R 27/30L SAE J 1239 701 FL12US 021217 1 23 4 13 4 10 1 8 7

15. 12 795 100 15 Saab 9-3 5D M06- List of components No. Name position Components 13 Lamp, parking light, trailer 27/30 Lamp, direction indicators/brake lights, trailer 258 Connector, towbar wiring harness, in the luggage compartment electrical distri- bution unit 701 Luggage compartment electrical distribution unit, on the wall behind the left-hand rear wheel housing 731 Trailer control module, in the luggage compartment electrical distri- bution unit Grounding points G3 In the luggage compartment below the left- hand light cluster

21. 12 795 100 21 Saab 9-3 5D M06- Template 1 F980A514 1 140mm 12mm

23. 12 795 100 23 Saab 9-3 5D M06- Template 2 F980A515 2 140mm 103mm

5. 12 795 100 5 Saab 9-3 5D M06- 7 Insert a screwdriver in the hole to reach under the catch. Bend carefully using the screwdriver to release the catch. 8 Pull the bumper shell away from the holders. F980A390 7 8

13. 12 795 100 13 Saab 9-3 5D M06- 26 Fit the hatch in the side trim.. 27 Raise the car. 28 Fit the two nuts holding the rear bumper air shield to the body and fit the screws holding the bumper shell to the wheel housings. F980A544 28 28 28 28 28

18. 18 12 795 100 Saab 9-3 5D M06- To detach the towball unit 1 Turn the sleeve to access the lock. Insert the key, turn it clockwise and remove the pin's lock. 2 Pull out the pin. 3 Fit the lock on the pin, turn the key anticlockwise and remove it. 4 Remove the ball unit. 5 Fit the cover. When the towbar is not in use, the wiring harness must be stored in the following location: Behind the hatch in the left-hand side trim. F980A136 4 3 1 1 3

2. 2 12 795 100 Saab 9-3 5D M06- 1 Body bracket 2 Ball mounting 3 Locking pin 4 Bolt (x4) 5 Screw (x2) 6 Nut (x4) 7 Reinforcement plate (x2) 8 Ball cap 9 Storage bag 10 Key (x2) 11 Wiring harness with diode box 12 Cable tie (x4) 13 Electronic module 14 Cover (purchased separately) 15 Ball 16 Spring washer 17 Nut 18 Load securing eyelet 19 Screw 20 Belt F980A397 12 16 15 17 14 10 11 14 13 5 2 3 9 1 8 7 7 6 4 18 19 20

6. 6 12 795 100 Saab 9-3 5D M06- 9 Release the catches using a screwdriver. Detach the shell from the strip. 10 Lift off the bumper shell. Cars with SPA: Pull out the wiring harness. 9 9

7. 12 795 100 7 Saab 9-3 5D M06- 11 Mount the towing bracket using bolts and nuts together with the reinforcements in the four bumper member holes and raise the car. 12 Fasten the towing bracket in the floor under the spare wheel well. 13 Tighten the bumper member mountings against the body as well as the screws, bolts and nuts holding the towing bracket against the bumper member and floor. Tightening torque, bumper member against body 50 Nm (37 lbf ft) Tightening torque, towing bracket against bumper member 50 Nm (37 lbf ft) Tightening torque, towing bracket against floor 50 Nm (37 lbf ft) F980A505 11,13 11,13 13 13 13 13 11 12,13 12,13

4. 4 12 795 100 Saab 9-3 5D M06- 1 Raise the car. 2 Remove the spoiler's centre nuts. 3 Remove the screws to the wheel housing. 4 Lower the car, open the boot lid and fold up the floor. 5 Remove the hatch in the left-hand luggage com- partment side trim. 6 Cars with SPA: Unplug the connector. F980A389 2 2 6 3 3 3

12. 12 12 795 100 Saab 9-3 5D M06- 24 SPA: Insert and plug in the connector. 25 Fit in the two tabs of the bumper shell under the holders and the outer corners between the wing liner and the mounting points at the wheel hous- ings. Press the bumper shell into place. F980A543 25 24

19. 12 795 100 19 Saab 9-3 5D M06- Important M06-07 without subwoofer (1) : Whenever the ball unit is removed it must be strapped into the eyelet in the left-hand rear corner of the spare wheel well. M06-07 with subwoofer (2) : Whenever the ball unit is removed it must be stored in the left-hand rear corner of the spare wheel well. The sub- woofer must be tightened. M08 with or without subwoofer (1): Whenever the ball unit is removed it must be strapped into the eyelet in the left-hand rear corner of the spare wheel well. F980A396 1 2

1. Saab 9-3 5D M06- 4900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 5D M06- Towbar Accessories Part No. Group Date Instruction Part No. Replaces 12 795 100 32 026 054 9:86-07 Oct 07 12 798 870 Jun 07 F980A033

3. 12 795 100 3 Saab 9-3 5D M06- The towing bracket was designed and tested in accordance with standard V-5 Class 2. Maximum permitted trailer weight: Trailer with brake: 3500 lbs (1587 kg) Trailer without brake: 1000 lbs (455 kg) Max. permissible ball pressure: 165 lbs (75 kg) Note Always check national legislation and regulations regarding mounting a towing bracket. Ensure that all requirements are complied with. Important The wiring harness must be connected following the description in these installation instructions. This is a requirement. If the wiring harness is con- nected in any other way, it could negatively affect the car's electrical system.

8. 8 12 795 100 Saab 9-3 5D M06- 14 Lower the car. 15 Plug the wiring harness connector into the REC and secure the wiring harness with four cable ties. 16 Fit the kit's electronic module in the REC and fit the fuse in position 8 in the rear electrical centre. 17 M06-07 without subwoofer: Fit the load secur- ing eyelet. M08 with or without subwoofer: Fit the load securing eyelet. 18 Fit the ball mounting, see “User instructions”. 19 Fit the ball to the mounting. Tightening torque 180 Nm (133 lbf ft) Important The blue/white (BU/WH) cable which is not con- nected in the connector must not be used, but must be secured together with the wiring harness in the nearest cable tie. F980A392 16 15 19 17

10. 10 12 795 100 Saab 9-3 5D M06- 22 M08, cars without a bumper skirt: 22.1 Print template 1 an d cut out the template. 22.2 Place template 1 (A) on the inside of the bumper shell against the upper marking and draw around the bottom edge of the template. 22.3 Cut/saw from the inside of the bumper shell (B). Important Check that the size of the template corresponds with the measurements after printing. Create your own template if it is not possible to get the printout to correspond with the measurements. WARNING Use of a saw and knife entails a risk of injury. Exercise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal pr otection equipment, such as protective gloves, safety goggles and hearing protection. Note Adapt the cut-out to the towbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper. 22 F980A541 A B

11. 12 795 100 11 Saab 9-3 5D M06- 23 M08, cars with a bumper skirt: 23.1 Print template 2 an d cut out the template. 23.2 Saw from the inside of the bumper accord- ing to the outer ma rkings up to (A). 23.3 Turnover the bumper 23.4 Place template 2 (B) on the outside of the bumper skirt against the edge (C). Centre between the cut slots and draw around the template. 23.5 Saw from the outside of the bumper skirt as per the marking (D). Important Check that the size of the template corresponds with the measurements after printing. Create your own template if it is not possible to get the printout to correspond with the measurements. 23 F980A542 B A A D C WARNING Use of a saw and knife entails a risk of injury. Exercise caution when cu tting. Check that the bumper shell is stably positioned before beginning to cut. Use personal prot ection equipment, such as protective gloves, safety goggles and hearing protection. Note Adapt the cut-out to the to wbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper.

9. 12 795 100 9 Saab 9-3 5D M06- 20 M06-07, cars without a bumper skirt Cut/saw from the inside of the bumper within the reinforcement ribs as per the marking (A). 21 M06-07, cars with a bumper skirt Cut/saw from the inside of the bumper within the reinforcement ribs as per the marking (B). WARNING Use of a saw and knife entails a risk of injury. Exercise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal pr otection equipment, such as protective gloves, safety goggles and hearing protection. Note Adapt the cut-out to the towbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper. 21 20 F980A540 B A WARNING Use of a saw and knife entails a risk of injury. Exercise caution when cu tting. Check that the bumper shell is stably positioned before beginning to cut. Use personal prot ection equipment, such as protective gloves, safety goggles and hearing protection. Note Adapt the cut-out to the to wbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper.

17. 12 795 100 17 Saab 9-3 5D M06- User instructions (keep in the car's Owner's Manual) To attach the towball unit 1 Remove the cover. 2 Fit the ball unit. 3 Insert the key in the pin's lock, turn it clockwise and remove the pin's lock. 4 Insert the pin into the towing bracket hole and fit the lock to the pin. Turn the key anticlockwise to lock the pin and then remove the key. Turn the lock sleeve to hide and protect the lock. WARNING To ensure that the towbar is coupled correctly and safely : • The coupling mechanism must always be well lubricated. Use a base oil with anti-corrosion properties and with a wide temperature range. We recommend that you contact an authorised Saab workshop regarding which lubricant is appropriate. • Always fit the protective cover when the tow- ball unit is not attached. • It must always be possible to detach and attach the towball un it without it jamming. F980A038 2 3 4 4

Weergaven

  • 680 Totale weergaven
  • 561 Websiteweergaven
  • 119 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 9 saabpartners.com
  • 24 www.saabpartners.com
  • 2 52.29.207.161
  • 5 54.154.214.138