Towbar, fixed 9-3 4D, CV

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

14. 14 12 789 094 Saab 9-3 4D/CV M03- Wiring diagram BK 2.5 C31-1 BK 2.5 C30-2 BK 2.5 C30-2 4 7 1 2 8 10 26 10 258 13 10 12 11 9 8 7 3 4 8 B1 B6 R-B 2 BK 4.0 G31-5 +54 10 22 38 J67 H102-1 91 YE/WH2 .5 P54-2 YE/WH2 .5 P54 2.5 RD/BU P54-2 9 GN/BU1 .0 C1-9 PK 1.0 C1-5 YE 1.0 C1-3 OG 1.0 C1-4 BN 1.0 C1-8 GN/WH1 .0 C1-10 GY 1.0 C1-6 RD 2.5 C30-2 11 BK 2.5 C31 J G3 5 RD 2.5 C30-1 TR-WH TR-WH TR-WH TR-WH TR-WH TR-WH +54 +30 +30 +30 26 25 23 24 18 11 9 22 3 21 2 5 20 16 15 12 6 17 14 +30 19 731 32 33 27L 13L 27R 13R 30 3 1 TR-WH TR-WH TR-WH TR-WH 12 11 6 5 2 4 10 9 8 7 13 701 F3L12 021212 3136 5 78 1 10 413 I-BUS

17. 12 789 094 17 Saab 9-3 4D/CV M03- Template 3 F980A51 6 3 84mm 103mm

16. 16 12 789 094 Saab 9-3 4D/CV M03- User instructions (keep in the car's Owners Manual) Important If the trailer is equipped with extra electrical equip- ment in addition to normal outer lighting (e.g. inner lighting or fan) and connected to the car via the trailer's connector, the trailer must be equipped with a 13-pin connector (installed according to ISO 11446) in order to allow for a separate power sup- ply. Important Cars with SPA: The SPA system will compensate for the towbar when measuring the distance behind the car.

2. 2 12 789 094 Saab 9-3 4D/CV M03- 1 Body bracket 2 Ball unit 3Screw (2) 4 Nut (x2) 5 Screw (x5) 6Screw (2) 7 Nut (x5) 8 Socket holder plate 9 Reinforcing plate (x2) 10 Ball guard 11 Wiring harness (13-pin) 12 Screw (x3) 13 Nut (x3) 14 Cable tie (x4) 15 Electronic module 16 Fuse 15 8 5 6 12 13 4 14 10 5 16 11 1 2 3 9 9 7 F980A028

6. 6 12 789 094 Saab 9-3 4D/CV M03- 13 Secure the towbar with bolts and nuts together with the reinforcements in the four holes which are in the bumper member and raise the car. 14 Fasten the towing bracket in the floor under the spare wheel well. 15 Tighten the bumper member mountings against the body and the bolts and nuts holding the tow- ing bracket against the bumper member and floor. Tightening torque, bumper member to body 50 Nm (37 lbf ft) Tightening torque, towing bracket to bumper member 50 Nm (37 lbf ft) Tightening torque, towing bracket to floor 50 Nm (37 lbf ft) 16 Remove the rubber grommet. F980A506 16 15 15 13,15 13,15 13 14,15 14,15 15 15

7. 12 789 094 7 Saab 9-3 4D/CV M03- 17 Insert the wiring harness through the hole in the body. 18 Fasten the wiring harness to the right-hand weld screw on the left-hand side of the towing bracket. 19 Fit the 13-pin connector to the connector holder plate. The cover should open upward. Important The seal between the connector and the connec- tor holder plate must be correctly mounted and should not be folded in anywhere. F980A030 18 17 19 19 19 19

8. 8 12 789 094 Saab 9-3 4D/CV M03- 20 Lower the car and run the wiring harness along the other wiring harnesses towards the left-hand side of the car and to the REC. 21 Plug the wiring harness connector into the REC and secure the wiring harness with 4 cable ties. 22 Fit the kit's electronic module in the REC and fit the fuse in position 8 in the REC. Important The blue/white (BU/WH) cable which is not con- nected in the connector must not be used, but must be secured together with the wiring harness in the nearest cable tie. F980A263 21 21 22 22 21 20,21 20,21 20,2 1 CV 4D

5. 12 789 094 5 Saab 9-3 4D/CV M03- 8 Remove the rear lamp clusters. 9 SPA: Unplug the connector. 10 Remove the bumper shell bolts that are located below the rear lamp clusters. 11 Remove the bumper bolts at the wheel housings. 12 Remove the bumper shell by pulling the sides outwards and then pulling the bumper shell rearwards. 8 8 8 10 12 11 8 F980A259 8 8 CV 4D 8

1. Saab 9-3 4D/CV M03- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 4D/CV M03- (EC 94/20, E4 00 1941) Towbar, fixed Accessories Part No. Group Date Instruction Part No. Replaces 12 804 702 32 026 046 9:86-03 Oct 07 12 789 094 Jun 07 F980A027

13. 12 789 094 13 Saab 9-3 4D/CV M03- 38 Fit the connector holder plate with connector to the towing bracket. 39 Mount the ball unit to the body bracket. Tightening torque 90 Nm (66.5 lbf ft) 40 Lower the car and check the bumper alignment. Adjust if necessary. 41 Carefully remove the user instruction page and give it to the customer together with the installa- tion instructions. Important Insert the screws from the right. F980A513 38 39

4. 4 12 789 094 Saab 9-3 4D/CV M03- 1 Raise the car. 2 Remove the two nuts holding the rear bumper air shield against the body and the two bolts holding the bumper shell against the wheel housings. 3 Lower the car and open the boot lid. CV: Remove the carpet on the luggage com- partment floor. 4 Remove the luggage compartment scuff plate. 5 4D: Remove the hatch in the luggage compart- ment left-hand side trim and lower the hatch on the right-hand side. 6 Remove the side scuff plate on the left-hand side. 7 Remove the clips for the left-hand side trim and fold the trim aside. CV: Unhook the strap on the rear side of the side trim and remove the connector from the luggage compartment lighting. Remove the side trim. 5 6 4 5 7 7 7 2 2 F980A022

10. 10 12 789 094 Saab 9-3 4D/CV M03- 25 M08, cars without bumper skirt Cut/saw from the inside of the bumper in accordance with the inner markings (A). WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection equipment, such as pro- tective gloves, safety goggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper. F980A51 0 25 A

3. 12 789 094 3 Saab 9-3 4D/CV M03- The towing bracket fulfils the requirements of 94/20/EEC. Maximum permitted trailer weight: Braked trailer: 1600 kg (3500 lbs.) Trailer without brakes: 50% of the towing vehicle's weight (vehicle in runni ng order), but no more than 750 kg (1650 lbs). Max. permissible towball pressure: 75 kg Maximum D-value: 8,91 kN Note Always check national legislation and regulations regarding mounting a towing bracket. Ensure that all requirements are complied with. Important The car must be inspected after the towing bracket is mounted. Show these instructions at the inspection.

12. 12 12 789 094 Saab 9-3 4D/CV M03- 27 SPA: Insert and plug in the connector. 28 Fit in the two tabs of the bumper shell under the holders and the outer corners between the wheel arch liner and the mounting points at the wheel arches. Press the bumper shell into place. 29 Fit the bumper shell bolts that are located below the rear lamp clusters. 30 Fit the bumper bolts at the wheel housings. 31 Fit and connect the rear lamp clusters. Check the fit against the boot lid moulding. 32 Fit the left-hand side trim. CV: Connect the luggage compartment lighting and hook the strap on. 33 Fit the side scuff plate on the left-hand side. 34 Fit the scuff plate. 35 4D: Fit the hatches in the luggage compartment side trims. CV: Fit the carpet on the luggage compartment floor. 36 Raise the car. 37 Fit the two nuts holding the air shield of the rear bumper against the body. Fit the two screws holding the bumper shell against the wheel housings. F980A51 2 29 29 28 30 37 37 28

15. 12 789 094 15 Saab 9-3 4D/CV M03- List of components No. Name position Components 13 Lamp, parking light, trailer 22 Main dashboard fuse box, on the short side of the instrument panel near the left-hand door 27 Lamp, direction indicators, trailer 30 Lamp, brake lights, trailer 32 Lamp, reversing lights, trailer 33 Lamp, rear fog lights, trailer 258 Connector, towbar wiring harness, in the luggage compartment electrical distri- bution box 701 Luggage compartment electrical distribution box, on the wall behind the left rear wheel housing 731 Trailer control module, in the luggage compartment electrical distri- bution box 102-pin connector H102-1 Lower left-hand A-pillar Crimp connections J Approx. 160 mm from the 13-pin connector J67 LHD: Approx. 150 mm from branching point front left floor lighting towards connector H102-1 RHD: Approx. 50 mm from branching point grounding point G40 towards grounding point G41 Grounding points G3 In the luggage compartment below the left- hand light cluster

11. 12 789 094 11 Saab 9-3 4D/CV M03- 26 M08, cars with bumper skirt: 26.1 Print out template 3 and cut out the tem- plate. 26.2 Saw from the inside of the bumper in accordance with the inner markings up to (A). 26.3 Turn the bumper over. 26.4 Position template 3 (B) on the outside of the bumper skirt against the edge (C). Centre between the sawn grooves and draw around the template. 26.5 Saw from the outside of the bumper skirt in accordance with the marking (D). Important Check that the size of the template corresponds with the specified dimensions after printing it out. Create your own template if it is not possible to make the printout correspond with the specified dimensions. Note Templates 1 and 2 are used for the detachable towbar and are not affected by these installation instructions. F980A511 26 26 26 A A B D C WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection eq uipment, such as pro- tective gloves, safety g oggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper.

9. 12 789 094 9 Saab 9-3 4D/CV M03- 23 M03-07, cars without bumper skirt Cut/saw from the inside of the bumper, inside the reinforcement ribs in accordance with the marking (A). 24 M03-07, cars with bumper skirt Cut/saw from the inside of the bumper, inside the reinforcement ribs in accordance with the marking (B). WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection equipment, such as pro- tective gloves, safety goggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper. 24 23 F980A50 9 B A WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection eq uipment, such as pro- tective gloves, safety g oggles and hearing protec- tion. Note The cut-out may need to be adapted to the tow- bar after fitting. Check that there is a small amount of play between towbar and bumper.

Weergaven

  • 552 Totale weergaven
  • 450 Websiteweergaven
  • 102 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 5 saabpartners.com
  • 19 www.saabpartners.com
  • 2 52.29.207.161
  • 2 54.154.214.138