Towbar, fixed 9-3 5D

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

19. 12 798 868 19 Saab 9-3 5D M06-

16. 16 12 798 868 Saab 9-3 5D M06- Wiring diagram BK 2.5 C31-1 BK 2.5 C30-2 BK 2.5 C30-2 4 7 1 2 8 10 26 10 258 13 10 12 11 9 8 7 3 4 8 B1 B6 R-B 2 BK 4.0 G31-5 +54 10 22 38 J67 H102-1 91 YE/WH2 .5 P54-2 YE/WH2 .5 P54 2.5 RD/BU P54-2 9 GN/BU1 .0 C1-9 PK 1.0 C1-5 YE 1.0 C1-3 OG 1.0 C1-4 BN 1.0 C1-8 GN/WH1 .0 C1-10 GY 1.0 C1-6 RD 2.5 C30-2 11 BK 2.5 C31 J G3 5 RD 2.5 C30-1 TR-WH TR-WH TR-WH TR-WH TR-WH TR-WH +54 +30 +30 +30 26 25 23 24 18 11 9 22 3 21 2 5 20 16 15 12 6 17 14 +30 19 731 32 33 27L 13L 27R 13R 30 3 1 TR-WH TR-WH TR-WH TR-WH 12 11 6 5 2 4 10 9 8 7 13 701 F3L12 021212 3136 5 78 1 10 413 I-BUS

20. 20 12 798 868 Saab 9-3 5D M06- Template 3 F980A516 3 84mm 103mm

5. 12 798 868 5 Saab 9-3 5D M06- 10 Insert a screwdriver in the hole to reach under the catch. Bend carefully using the screwdriver to release the catch. 11 Pull the bumper shell away from the holders. F980A374 10 11

14. 14 12 798 868 Saab 9-3 5D M06- 36 Fit the scuff plate. 37 Fit the panel in the side trim. 38 Raise the car. 39 Fit the two nuts holding the rear bumper air shield to the body and the bolts holding the bumper shell to the wheel housings. F980A521 39 39 39 36 36 39 39

18. 18 12 798 868 Saab 9-3 5D M06- User instructions (to be kept in the driver's manual) Important If the trailer is equipped with extra electrical equip- ment in addition to normal outer lighting (e.g. inner lighting or fan) and connected to the car via the trailer's connector, the trailer must be equipped with a 13-pin connector (installed according to ISO 11446) in order to allow for a separate power supply. Important Cars with SPA : The SPA system will compensate for the towbar when measuring the distance behind the car.

2. 2 12 798 868 Saab 9-3 5D M06- 1 Body bracket 2 Ball unit 3 Bolt (x2) 4 Nut (x2) 5 Bolt (x5) 6 Bolt (x2) 7 Nut (x5) 8 Socket holder plate 9 Reinforcement plate (x2) 10 Ball guard 11 Wiring harness (13-pin) 12 Bolt (x3) 13 Nut (x3) 14 Cable tie (x4) 15 Electronic module 16 Fuse 15 8 5 6 12 13 4 14 10 5 16 11 1 2 3 9 9 7 F980A381

6. 6 12 798 868 Saab 9-3 5D M06- 12 Release the catches using a screwdriver. Detach the shell from the moulding. 13 Lift off the bumper shell. Cars with SPA: Pull out the wiring harness. F980A450 12 12

7. 12 798 868 7 Saab 9-3 5D M06- 14 Secure the towbar with bolts and nuts together with the reinforcements in the four holes which are in the bumper member and raise the car. 15 Fasten the towing bracket in the floor under the spare wheel well. 16 Tighten the bumper member mountings to the body as well as the screws, bolts and nuts hold- ing the towing bracket to the bumper member and floor. Tightening torque, bumper member to body 50 Nm (37 lbf ft) Tightening torque, towing bracket to bumper member 50 Nm (37 lbf ft) Tightening torque, towing bracket to floor 50 Nm (37 lbf ft) 17 Remove the rubber grommet. F980A503 17 16 16 14,16 14,16 14 15,16 15,16 16 16

8. 8 12 798 868 Saab 9-3 5D M06- 18 Insert the wiring harness through the hole in the body. 19 Fasten the wiring harness to the right-hand weld screw on the left-hand side of the towing bracket. 20 Fit the 13-pin connector on the socket holder plate. The cover should open upward. Important The seal between the connector and the socket holder plate must be correctly mounted and should not be folded in anywhere. F980A376 19 18 20 20 20 20

9. 12 798 868 9 Saab 9-3 5D M06- 21 Lower the car. 22 Remove the clip holding the foam plastic block on the left-hand side. 23 Carefully lift up the foam plastic block and guide the wiring harness underneath it. 24 Plug the wiring harness connector into the REC and secure the wiring harness with four cable ties. 25 Fit the kit's electronic module in the REC and fit the fuse in position 8 in the REC. 26 Fit the clip for the foam plastic block. Important The blue/white (BU/WH) cable which is not con- nected in the connector must not be used, but must be secured together with the wiring harness in the nearest cable tie. F980A377 25 24 23 22,26

1. Saab 9-3 5D M06- 3900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 5D M06- (EC 94/20, E4 00 2526) Towbar, fixed Accessories Part No. Group Date Instruction Part No. Replaces 12 795 098 32 026 052 9:86-05 Oct 07 12 798 868 Jun 07 F980A027

13. 12 798 868 13 Saab 9-3 5D M06- 31 SPA: Insert and plug in the connector. 32 Fit in the two tabs of the bumper shell under the holders and the outer corners between the wheel arch liner and the mounting points at the wheel arches. Press the bumper shell into place. 33 M06-07 with subwoofer: Fold down and screw in the subwoofer. 34 Fit the floor section on the left-hand side. 35 Fold down the floor. F980A520 32 31

15. 12 798 868 15 Saab 9-3 5D M06- 40 Fit the socket holder plate with connector on the towing bracket. 41 Fit the ball unit to the body bracket. Tightening torque 90 Nm (66.5 lbf ft) 42 Lower the car and check the bumper alignment. Adjust if necessary. 43 Carefully remove the user instruction page and give it to the customer together with the installa- tion instructions. Important Insert the bolts from the right. F980A522 40 41

11. 12 798 868 11 Saab 9-3 5D M06- 29 M08, cars without a bumper skirt Cut/saw from the inside of the bumper as per the markings (A). WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection equipment, such as pro- tective gloves, safety goggles and hearing protec- tion. Note Adapt the cut-out to the towbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper. F980A518 29 A

4. 4 12 798 868 Saab 9-3 5D M06- 1 Raise the car. 2 Remove the spoiler's centre nuts. 3 Remove the screws to the wheel housing. 4 Lower the car and open the boot lid. 5 Fold up the floor. 6 M06-07 with subwoofer: Unscrew the screws holding the subwoofer, lift it up and secure it. 7 Remove the luggage compartment scuff plate. 8 Remove the panel in the left-hand luggage com- partment side trim. 9 Cars with SPA: Detach the connector. Important The scuff plate is fitted with two clips. F980A373 7 2 2 9 3 3 3 7

3. 12 798 868 3 Saab 9-3 5D M06- The towing bracket fulfils the requirements of 94/20/EEC. Maximum permitted trailer weight: Braked trailer: 1600 kg (3500 lbs.) Trailer without brakes: 50% of the towing vehicle's weight (vehicle in runni ng order), but no more than 750 kg (1650 lbs). Max. permissible towball pressure: 75 kg Maximum D-value: 9.0 kN Note Always check national legislation and regulations regarding mounting a towing bracket. Ensure that all requirements are complied with. Important The car must be inspected after the towing bracket is mounted. Show these instructions at the inspection.

17. 12 798 868 17 Saab 9-3 5D M06- List of components No. Name position Components 13 Lamp, parking light, trailer 22 Main fuse box, dashboard, on the short side of the dashboard by the left-hand door 27 Lamp, direction indicators, trailer 30 Lamp, brake lights, trailer 32 Lamp, reversing lights, trailer 33 Lamp, rear fog lights, trailer 258 Connector, towbar wiring harness, in the luggage compartment electrical centre 701 Luggage compartment electrical centre, on the wall behind the left rear wheel housing 731 Trailer control module, in the luggage compartment electrical centre 102-pin connector H102-1 Lower left-hand A-pillar Crimp connections J Approx. 160 mm from the 13-pin connector J67 LHD: Approx. 150 mm from branching point front left floor lighting towards connector H102-1 RHD: Approx. 50 mm from branching point grounding point G40 towards grounding point G41 Grounding points G3 In the luggage compartment below the left light cluster

12. 12 12 798 868 Saab 9-3 5D M06- 30 M08, cars with a bumper skirt: 30.1 Print template 3 an d cut out the template. 30.2 Saw from the inside of the bumper as per the inner markings up to (A). 30.3 Turnover the bumper. 30.4 Place template 3 (B) on the outside of the bumper skirt against the edge (C). Centre between the cut slots and draw around the template. 30.5 Saw from the outside of the bumper skirt as per the marking (D). Important Check that the size of the template corresponds with the measurements after printing. Create your own template if it is not possible to get the printout to correspond with the measurements. Note Templates 1 and 2 are used for a removable tow- bar and are not affected by these installation instructions. F980A519 30 30 30 A A B D C WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection eq uipment, such as pro- tective gloves, safety g oggles and hearing protec- tion. Note Adapt the cut-out to the to wbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper.

10. 10 12 798 868 Saab 9-3 5D M06- 27 M06-07, cars without a bumper skirt Cut/saw from the inside of the bumper within the reinforcement ribs as per the marking (A). 28 M06-07, cars with a bumper skirt Cut/saw from the inside of the bumper within the reinforcement ribs as per the marking (B). WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection equipment, such as pro- tective gloves, safety goggles and hearing protec- tion. Note Adapt the cut-out to the towbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper. 28 27 F980A517 B A WARNING Use of a saw and knife entails a risk of injury. Exer- cise caution when cutting. Check that the bumper shell is stably positioned before beginning to cut. Use personal protection eq uipment, such as pro- tective gloves, safety g oggles and hearing protec- tion. Note Adapt the cut-out to the to wbar after installation if necessary. Check that there is a small amount of play between the towbar and bumper.

Weergaven

  • 586 Totale weergaven
  • 485 Websiteweergaven
  • 101 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 5

  • 9 www.saabpartners.com
  • 3 52.29.207.161
  • 5 saabpartners.com
  • 1 52.211.236.180
  • 4 54.154.214.138