Towing hooked, fixed 9-5 5D

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

7. 48 25 535 7 Saab 9-5 5D 23 Pull off the bottom of the sealing strip around the luggage compartment opening. 24 Replace the upper section of the bumper shell by first positioning it on the four bolts on the bumper member. Then press on the upper sec- tion with the hooks over the edge. Tighten the bolts. 25 Put back the sealing strip around the luggage compartment opening. 26 Fit the rear lights. 27 Fit the foam blocks over the bumper mountings in the luggage compartment and put back the storage box and outer sections of the luggage compartment floor. 28 Place the installation instructions inside the car. E980A055 26 26 24 27 27 27 23,25

3. 48 25 535 3 Saab 9-5 5D 1 Undo the outer sections of the luggage compartment floor. 2 Lift up the storage box and pull off the foam blocks (2 on each side) at the back of the body. 3 Remove the bumper. 4 Remove the rear lights by loosening the two covers over the screws, removing the screws and detaching the fasteners at the front of the lamps. 5 Remove the towing lug and fit the rubber plug. E980A051 4 4 5 1 1 2 3

4. 4 4825535 Saab 9-5 5D 6 Slightly loosen the screws on the upper part of the bumper shell and carefully pull the shell away from its snap fasteners. 7 Remove the bumper shell supports and cut out the left-hand support as illustrated and the right- hand support correspondingly. 8 Cut along the inner marking in the bumper shell for the towing hook and the marking for the wir- ing harness terminal box. Also remove the tab remaining on the bottom of the bumper between the cut-outs for the hook and the terminal box. 9 Remove the spacers from the bumper rail and fit the reinforcement instead. Tighten the four bumper retaining nuts to secure the reinforce- ment. 10 Drill the four holes in the bumper rail with a 6.5 mm drill. 11 Fit the taptite screws. Tightening torque 25 Nm (20 lbf ft). 12 Remove the nuts and position the bumper shell supports. E980A052 11 11 6 6 6 10 (ø6.5mm) 8 9 9 12 7 30 45

5. 48 25 535 5 Saab 9-5 5D 13 Scrape off the sealant from the body where the bumper reinforcement will make contact, posi- tion the bumper and fit it to the body with the top two nuts. 14 Drill 10 mm holes in the sleeves, the rear end panel and the reinforcement. 15 Remove the bumper and clean all the drill cut- tings from the luggage compartment. 16 Deburr the holes and remove any loose cuttings and flakes of paint. 17 Fit the seals onto the body (self-adhesive) and apply cavity sealant Terotex HV 400 (part no. 30 15 930) to the interior surfaces. Apply anti-cor- rosion agent to the surfaces from which the body sealant was scraped as well. 18 Fit the selected wiring harness according to the instructions supplied with it. Important Take care not to damage the car’s wiring harness. ø10 mm E980A053 17 14

1. 48 25 535 1 Saab 9-5 5D 9-5 Monteringsanvisning SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTALLATIONS DE MONTAGE SITdefault Saab 9-5 5D Towing hooked, fixed 1 Hook unit 2 Reinforcement 3Bolts 4 Seal 5 Rubber plug Accessories Part No. Group Date Instruction Part No. Replaces 400 110 565 400 110 615 8:60-28 Apr 98 48 25 535 E980A050 3 3 1 5 4 2

6. 6 4825535 Saab 9-5 5D X Eyebolt for fastening the trailer/caravan safety chain 19 Remove the screw in one of the holes in the bumper rail and fit the hook unit to the bumper. Tightening torque 40 Nm (30 lbf ft). 20 Position the bumper and fit it to the car with four nuts. Tightening torque 40 Nm (30 lbf ft). Replace the screw by the wheel housing. 21 Screw the reinforcement to the car. Tightening torque 40 Nm (30 lbf ft). 22 Fit the screws and nut plates securing the hook to the body. Tightening torque 40 Nm (30 lbf ft). E980A054 22 X 19 21 21 20 19 19

2. 2 4825535 Saab 9-5 5D 400 110 565 (Saab part no. 48 25 501) for cars without level control . 400 110 615 (Saab part no. 48 27 853) for cars with level control . The towing hook complies with 94/20/EEC requirements. Maximum permitted trailer load: Braked trailer: 1800 kg Unbraked trailer: 50% of the weight of the towing vehicle in running order or max. 750 kg (1650 lbs). Max. permitted load on hook: 75 kg Total weight: 8.2 kg Fit and connect the wiring harness as directed in the instructions supplied with it. Note Always check with national legal requirements and regulations for fitting towing hooks. Make sure that they are fulfilled. Important The car must be inspected by the relevant authorities after fitting a towing hook. Produce these directions at the inspection.

Weergaven

  • 501 Totale weergaven
  • 422 Websiteweergaven
  • 79 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 9 saabpartners.com
  • 7 www.saabpartners.com
  • 3 52.29.207.161
  • 4 54.154.214.138