Upgrade to Premium 300 sound system 9-3 4D 1

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

4. 4 12 788 464 Saab 9-3 4D M03- 1 Open the hatchback. 2 Remove the battery's negative cable and remove the key from the ignition. 3 Lower the rear seat backrest. 4 Detach the clips holding the parcel shelf trim. 5 Pull the parcel shelf trim straight out. 6 Remove the cover washer from the C-pillar trim. Use removing tool 82 93 474. 7 Undo the screw from the C-pillar trim. Do not unscrew it completely as an expander is fitted to the screw which can be lost. 8 Remove the C-pillar trim by carefully pulling the trim forwards, together with the screw. 9 Fold the luggage compartment floor forwards. 10 In the luggage compartment, remove the hatch in the left-hand side trim and lower the hatch on the right-hand side. 11 Remove the clips for the left-hand side trim and fold the trim away. Do the same on the right- hand side. F930A086 5 8 8 7 6 4 10 11

8. 8 12 788 464 Saab 9-3 4D M03- Cars where there is no bracket at the REC 27 Remove the front scuff plate on the left-hand side of the car. 28 Remove the lower section of the A-pillar trim on the left-hand side. 29 Position the left-hand front seat in its most for- ward position and fold the backrest forwards. 30 Remove the two rear retaining screws from the seat. 31 Angle the seat forwards. 32 Pull the seat back so that the fitting hooks loosen from their positions. Fold the whole seat backwards. 33 Remove the amplifier. F930A090 30 30 28 27 32 33 33

2. 2 12 788 464 Saab 9-3 4D M03- 1 Amplifier 2 Treble speaker (x4) 3 Bass speaker (x2) 4 Screw (x8) 5 Wiring harness 6 Cover, connector housing 7 Optical cable connector, 2-pin 8 Cable tie with clip 9 Fibre optic cable (omitted from illustration) (used only when there is other equipment in the bracket in the luggage compartment) The following items are also required (ordered separately) Bracket for baggage compartment equipment (certain cars), comprising: –Bracket – Screw (x3) –Nut – Clip nut – Side trim F930A085 8 6 7 1 3 5 2 4 3 2

6. 6 12 788 464 Saab 9-3 4D M03- 18 Fit the treble speakers by pressing them securely into the holes. Connect the speakers and guide the foam plastic sleeve on each wiring harness over the connector. 19 Connect and fit the wide range speakers. 20 Connect the bass speakers and fit them with the appropriate cover pointed to the side. Note The treble speakers must be fitted with the connections pointed in different directions. F930A088 18 19 20 20 20 19 19 18 20

12. 12 12 788 464 Saab 9-3 4D M03- Cars where there is no bracket at the REC 50 Set the seat in its correct position, be careful that the fitting hooks locate themselves correctly into their brackets, and fit the rear retaining screws. Tightening torque 30 Nm (22 lbf ft) 51 Push the seat backwards and reset the position of the back rest. 52 Fit the A-pillar trim. 53 Fit the scuff plate. F930A094 50 50 52 53 50

1. Saab 9-3 4D M03- 900 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 4D M03- Upgrade to Premium 300 sound system Accessories Part No. Group Date Instruction Part No. Replaces 12 787 154 32 000 556 9:36-22 Feb 05 12 788 464 12 788 464 Nov 02 F930A084

13. 12 788 464 13 Saab 9-3 4D M03- Cars where there is no bracket at the REC 54 Position the bracket in the luggage compartment. 55 Fit the clip nut in the square hole by the REC. 56 Locate the connector for the amplifier by the REC. Remove the tape and pull the connector forwards. 57 Fit the cover on the amplifier's connector. 58 Locate the fibre optic cable by the REC. 59 Remove the protective cover from the fibre optic cables' connections. 60 Fit the green marked connection on the fibre optic cable in position 1 in the small connector to the control unit and the unmarked connection on the fibre optic cable in position 2 in the small connector. Fit the lock. 61 Fit the small connector to the large connector. Proceed to step 73. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A095 58 56 61 57 55 57 60 Important For cars without green marked fibre optic cable the fibre optic cable marked with tape earlier must be fitted in position 2 and the other unmarked con- nection must be fitted in position 1.

17. 12 788 464 17 Saab 9-3 4D M03- 80 Remove the front speaker grilles (tool 82 93 474 is recommended). 81 Remove the wide range speakers. 82 Remove the connector from the wide range speakers and connect the treble speakers. Guide the foam plastic sleeve over the connector. 83 Connect the connector from the treble speakers to the wide range speakers. 84 Guide down the wiring harness in the wide range speakers' holes and position the wiring harness for the treble speakers in the respective groove. 85 Fit the treble speakers by pressing them firmly into the holes. 86 Fit the wide range speakers. 87 Fit the speaker grilles. 88 Connect the negative battery cable. 89 Adjust the time and date. 90 Synchronise the remote control code by setting the key in the ignition. 91 Activate window lift pinch protection function by operating the side windows up and down twice. An audible confirmation will sound when activa- tion is complete. 92 Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 93 Check that the system is working. Important This must be done with all keys otherwise the remote controls will not work F930A099 81,86 80,87 80,87 81,86 85 83 82 Note The diagnostic tool will on some occasions need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display.

7. 12 788 464 7 Saab 9-3 4D M03- 21 Position the C-pillar trim. Make sure that the screw with expander is in the correct position. 22 Tighten the screw. Tightening torque 2 Nm (1.5 lbf ft) 23 Fit the cover washer to the C-pillar trim. 24 Slide in the parcel shelf trim. Make sure the lugs fully engage the mountings in the parcel shelf plate. 25 Fit the clips to the parcel shelf trim. 26 Raise the backrest. Check that the backrest is locked. Cars where there is no bracket at the REC: Continue with step 27. Cars where the bracket at the REC is fitted: Continue with step 62. WARNING Be careful not to damage the collision curtain. Damage can result in the collision curtain not pro- viding the intended protection to occupants in the event of a side collision. F930A089 25 22,23 21 21 24 24 24

15. 12 788 464 15 Saab 9-3 4D M03- Cars where the bracket at the REC is fitted 69 CD changer and/or DVD player is fitted: Fit one connection on the set's fibre optic cable in position 1 in the set's connector. Fit the lock. 70 CD changer and/or DVD player is fitted: Fit the other connection on the set's fibre optic cable in position 2 in the removed connector. Fit the lock. 71 CD changer and/or DVD player is fitted: Fit the small connector in the large connector for the CD changer or DVD player. 72 CD changer and/or DVD player is fitted: Con- nect the CD changer or DVD player connector. Proceed to step 73. F930A097 70 69 71 69

5. 12 788 464 5 Saab 9-3 4D M03- 12 Remove the covers from the bass speakers by pressing them upwards from below. 13 Remove the connector from the wide range speakers in the parcel shelf and remove the speakers. 14 Remove the wiring harness from the parcel shelf and remove the connection in the REC. 15 Fit the new wiring harness above the parcel shelf and connect it. 16 Guide down the cable for the speakers in the holes for the wide range speakers in the parcel shelf. 17 Guide down the fibre optical cable on the right- hand side of the car and affix it using a cable tie and clip. Important Handle the fibre optic cables with care or the sig- nal may be distorted. · Do not bend the cable in a radius smaller than 25 mm. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A087 14 17 17 12 12 13 13 14

14. 14 12 788 464 Saab 9-3 4D M03- Cars where the bracket at the REC is fitted 62 Remove the bracket and take it out to facilitate access. 63 Locate the connector for the amplifier by the REC. Remove the tape and pull the connector forwards. 64 Fit the cover on the amplifier's connector. 65 CD changer or DVD player is fitted by the REC: Remove the CD changer / DVD player connector and remove the small connector from the large connector. CD changer and DVD player is fitted by the REC: Remove the CD changer connector and remove the small connector from the large connector. 66 CD changer and/or DVD player is fitted: Remove the fibre optic cable connected to posi- tion 2 in the removed connector by opening the lock in the connector and carefully lifting the hook. 67 CD changer and/or DVD player is fitted: Fit the connection on the fibre optic cable in position 2 in the set's connector. 68 CD changer and/or DVD player is fitted: Remove the protective cover from the connec- tions on the accessory set's fibre optic cable. F930A096 66 65 66 67

11. 12 788 464 11 Saab 9-3 4D M03- Cars where there is no bracket at the REC 43 Locate the loose fibre optic cable and the con- nector with the fibre optic cables connected by the left-hand A-pillar (taped to the cable duct). 44 Lift up the connector lock tab. 45 Remove the fibre optic cable from the position in the connector where the arrow points outwards, to the fibre optic cable. 46 Remove the fixing tape from the loose fibre optic cable. 47 Remove the protective cover from the connection. 48 Fit the protective cover onto the removed fibre optic cable connection and carefully move the fibre optic cable aside in order to prevent dam- age, and position it behind the wiring harness. 49 Fit the connection to the new fibre optic cable in the connector and fit the lock tab. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. Important Handle the fibre optic cables with care or the sig- nal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A093 44 43 43 49

10. 10 12 788 464 Saab 9-3 4D M03- Cars where there is no bracket at the REC 39 Remove the cover to the cable duct, check that the fibre optic cable cannot twist and fit the con- nection on the fibre optic cable in position 1 in the small connector to the amplifier. Fit the lock. 40 Fit the small connector to the large connector. 41 Fit the cover to the cable duct, draw back the carpet and guide out the connector and the cables through the hole in the carpet. 42 Connect and fit the amplifier. Important Handle the fibre optic cables with care or the signal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A092 42 39 39 42 39,41 40

9. 12 788 464 9 Saab 9-3 4D M03- Cars where there is no bracket at the REC 34 Locate the green marked fibre optic cable by the amplifier. If there is no colour marking and there is no bracket by the REC: Follow the instructions in steps 58 and 59 in these fitting instructions, shine a light onto the fibre optic cable by the amplifier and check the fibre optic cables in the luggage compartment to identify the relevant fibre optic cable. Mark with a piece of tape. 35 Remove the fibre optic cables' connector (the small connector) from the amplifier's connector. 36 Remove the fibre optic cable connected to posi- tion 1 by opening the connector locking clip and carefully lifting the hook. 37 Remove the protective cover from the connec- tion on the extra fibre optic cable. 38 Fit the protective cover onto the removed fibre optic cable connection and carefully move the fibre optic cable aside in order to prevent damage. Important Handle the fibre optic cables with care or the sig- nal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A091 34 35 36 36

3. 12 788 464 3 Saab 9-3 4D M03- Bus Communication Many parts of the car's electrical system communi- cate using a bus. There are three types of bus com- munication: P-bus (Powertrain Bus), I-bus (Instru- ment Bus) and O-bus (Optical bus). The audio system communicates via the O-bus together with the navigation system, the telephone system and others. The O-bus is optical and is a ring bus. Two fibre opti- cal cables are connected to each control module on the bus, one fibre optical cable for receiving and one for sending. Messages received are converted by each control module from a fibre optic signal to elec- trical and then converted back to optical for sending. The O-bus data transfer rate is 25 Mbit/s. AMP1 is an amplifier below the left-hand front seat AMP2 is an amplifier by the REC CDC is a CD changer by the REC DVD is a DVD player by the REC When fitting new equipment to be connected to the O-bus it is important that it is connected into the cor- rect side of the existing equipment. Important It is very important that everything connected to the O-bus is connected in a specific order, see illustration, and that the ring is closed the whole time. Connection in any other way than that described in these fitting instructions may result in several of the car's systems failing to work. F930A100 1 2 CDC 1 2 DVD 1 2 AMP2 1 2 1 2 AMP2 CDC 1 2 1 2 AMP2 DVD 1 2 1 2 DVD CDC 1 2 1 2 1 2 AMP2 DVD CDC 2 1 Important Handle the fibre optic cables with care or the sig- nal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not splice the cables. · Do not bend the cable in a radius smaller than 25 mm. · Do not expose the cable to temperatures exceeding 85 °C. · Keep the cable ends free from dirt and grime. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction.

16. 16 12 788 464 Saab 9-3 4D M03- 73 Guide the connector for the amplifier through the bracket. 74 Remove the protective cover over the fibre optic cable connection on the amplifier. 75 Fit the amplifier in the bracket, a clicking sound should be heard, connect the amplifier and align the bracket. 76 Fit the bracket. Tighten the nut on the bracket's top side. 77 Fit the side trims. 78 Fit the new cover in the luggage compartment's left-hand side trim and fold up the cover on the right-hand side. 79 Lower the luggage compartment floor. Important Handle the fibre optic cables with care or the signal may be distorted. · Do not bend the cable in a radius smaller than 25 mm. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A098 75 75 76 76 76 76 74 76 76 Important Handle the fibre optic cables with care or the signal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · The cable should not lie against any sharp edges as this may cause increased signal reduction.

Weergaven

  • 597 Totale weergaven
  • 501 Websiteweergaven
  • 96 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 4

  • 20 www.saabpartners.com
  • 3 52.29.207.161
  • 2 saabpartners.com
  • 5 54.154.214.138