Upgrade to Prestige 300 sound system 9-3 CV

English

Delen op sociale netwerken

Koppeling delen

Gebruik permanente koppeling om te delen via sociale media

Deel met een vriend

Alstublieft in te loggen voor het versturen van deze document per e-mail!

In uw website insluiten

Kies de startpagina

5. 12 832 514 5 Saab 9-3 CV M04- 11 Carefully remove the speaker grille from the left- hand rear side trim. Use removal tool 82 93 474. 12 Remove the screw that holds the rear side trim on the left-hand side. 13 Lift the side trim upwards. Retain the rubber protectors. 14 Unhook the control module from the side trim, but do not remove the control module connector as this means a diagnostic trouble code being generated. 15 Remove the speaker connector and remove the side trim. F930A208 11 12 13 15 14

6. 6 12 832 514 Saab 9-3 CV M04- 16 Raise the soft top and open the boot lid. 17 Remove the battery's minus cable and take the key from the ignition. 18 Remove the carpet on the luggage compart- ment floor and remove the luggage compart- ment scuff plate. 19 Remove the side scuff plate on the left-hand side. 20 Remove the clips for the left-hand side trim and fold the trim aside. Unhook the strap on the rear side of the side trim and remove the connector from the luggage compartment lighting. Remove the side trim. F930A209 19 20 20 20 18 18 20

8. 8 12 832 514 Saab 9-3 CV M04- Cars without console by the REC 24 Remove the scuff plate on the left-hand side of the car. 25 Remove the lower section of the A-pillar trim on the left-hand side. 26 Position the left-hand front seat in its most for- ward position and fold the backrest forwards. 27 Remove the connector from the amplifier. F930A211 25 24 27

12. 12 12 832 514 Saab 9-3 CV M04- Cars without console by the REC 44 Fit the A-pillar trim. 45 Fit the scuff plate. F930A215 44 45

17. 12 832 514 17 Saab 9-3 CV M04- 69 Fit the left-hand side trim, connect the luggage compartment lighting and hook the strap on. Fit the clips. 70 Fit the side scuff plate on the left-hand side. 71 Fit the scuff plate and fit the carpet on the luggage compartment floor. F930A220 69 69 69 71 71 70 69

18. 18 12 832 514 Saab 9-3 CV M04- 72 Remove the front speaker grilles (tool 82 93 474 is recommended). 73 Remove the wide range speakers. 74 Remove the connector from the wide range speakers and connect the treble speakers. Guide the foam plastic sleeve over the connector. 75 Connect the connector from the treble speakers to the wide range speakers. 76 Guide down the wiring harness in the wide range speakers' holes and position the wiring harness for the treble speakers in the respective groove. 77 Fit the treble speakers by pressing them firmly into the holes. 78 Fit the wide range speakers. 79 Fit the speaker grilles. F930A221 73,78 72,79 72,79 73,78 77 75 74

19. 12 832 514 19 Saab 9-3 CV M04- 80 Connect the negative battery cable. 81 Fold down the soft top completely, but allow the soft top cover to remain open. 82 Check that the damp protection in the left-hand side trim is intact and replace if necessary. 83 Connect the speaker connector, fit the side trim and press it down. Check that the rubber protec- tors are in place. 84 Fit the screw that holds the side trim, fold the inner lip on the door opening seal over the side trim front edge and lift the bracket on the soft top cover seal over the side trim. F930A222 84 83 83 82

4. 4 12 832 514 Saab 9-3 CV M04- 1 Fold down the soft top completely, but allow the soft top cover to remain open. 2 Open the rear side window on the left-hand side completely. 3 Remove the screws which hold the rear seat cushion at the front edge. 4 Lift up the cushion and pull it forwards so that it loosens. 5 Pull up both of the rear head restraints to the highest position. 6 Press in the lock on the head restraints' sleeves. Hold the lock pressed in and remove the head restraints. 7 Remove the screws for the seat belts' lower mounting. 8 Remove the two screws for the backrest cushion upper mounting. 9 Pull the backrest cushion lower section forwards and lift the backrest cushion upwards. 10 Press out the seat belt guide from the backrest cushion and move the seat belt out from the guide and the backrest cushion. F930A207 4 4 6 6 3 3 7 8 9 10 10

2. 2 12 832 514 Saab 9-3 CV M04- 1 Amplifier 2 Treble speaker (x4) 3 Bass speaker (x2) 4 Screw (x8) 5 Cover, connector housing 6 Optical cable connector, 2-pin 7 Fibre optic cable (x3) – Between the units in the luggage compart- ment console (455 mm long) – Amplifier - bracket, luggage compartment (1850 mm long) – Bracket, luggage compartment - Torsion compartment (1195 mm long) 8 Sound insulation, rubber strip – 2100 mm –850 mm – 750 mm (x2) 9 Sound insulation, felt cloth (x2) 10 Cable tie (x7) In addition, the following items are required (ordered separately) Console for equipment in the luggage compartment (certain cars) F930A390 10 5 6 1 3 2 4 3 2 7 8 9

20. 20 12 832 514 Saab 9-3 CV M04- 85 Carefully remove the speaker grille from the left- hand rear side trim. Use removal tool 82 93 474. 86 Undo the screws that hold the wide range speaker in the right-hand side trim. Remove the wide range speaker and remove the connector from the speaker. 87 Cut into the side trim for the treble speaker. 88 Fit in the treble speaker's wiring harness through the opening in the side trim and connect the connector to the connector for the wide range speaker. 89 Fit the treble speaker by pressing it securely into the side trim. 90 Connect the wide range speaker and fit the foam rubber sleeve over the connector. 91 Fit the wide range speaker in the side trim. 92 Fit the speaker grille. 93 Repeat steps 85-92 on the right-hand side of the car. 94 Close the soft top cover. Note The treble speakers must be fitted with the con- nections pointing in different directions. F930A223 85,92 86 86 91 89 88 88 90 90 87 91

13. 12 832 514 13 Saab 9-3 CV M04- Cars without console by the REC 46 Position the bracket in the luggage compartment. 47 Fit the clip nut in the square hole by the REC. 48 Locate the connector for the amplifier by the REC. Remove the tape and pull the connector forwards. 49 Fit the cover on the amplifier's connector. 50 Locate the fibre optic cable by the REC. 51 Remove the protective cover from the fibre optic cables' connections. 52 Fit the green-marked connection on the fibre optic cable in position 1 in the small connector and the unmarked connection on the fibre optic cable in position 2 in the small connector. Fit the lock. 53 Fit the small connector to the large connector. Proceed to step 65. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A216 47 47 50 48 53 49 49 52 Important For cars without green marked fibre optic cable the fibre optic cable marked with tape earlier must be fitted in position 2 and the other unmarked connection must be fitted in position 1.

21. 12 832 514 21 Saab 9-3 CV M04- 95 Fit the sealing strip (2100 mm) on the back of the rear seat backrest. 96 Fit the sealing strip (850 mm) and the felt cloths on the back of the rear seat backrest. 97 Fit both sealing strips (750 mm) on the steel col- lars around the backrest speakers. 98 Fit the rear seat belts into the belt guide and fit the guides in the backrest cushions by pressing them in. Fit the backrest cushion from above and press it down securely. 99 Fit the two screws for the backrest cushion upper mounting. 100Fit the screws for the seat belts' lower mounting. 101Fit the rear head restraints in the sleeves. 102Fit the seat cushion and fit the screws in the seat cushion front edge. 103Adjust the time and date. 104Synchronise remote control code by inserting the key into the ignition. 105Activate window lift pinch protection function by operating the side windows up and down twice. An audible confirmation will sound when activa- tion is complete. 106Connect the diagnostic tool, select car and model year, select “All”, select “Add/Remove”, select the accessory and then “Add”. 107Check that the system is working. Important Repeat this procedure with all keys. Otherwise, the remote controls will not function. F930A391 98 98 100 95 96 96 99 98 102 102 102 97 Note The diagnostic tool will on some occasions need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display.

1.  

 900 Installation instructions  

    



   



    

 SITdefault       !"  !#$ !%!& 

   

  

   

 '( )( * (  *** +,(,  * '( )( *' '( )( *' -#.  F930A205

7. 12 832 514 7 Saab 9-3 CV M04- 21 Remove the bass speakers' covers. 22 Locate the bass speakers' connectors. 23 Connect and fit the bass speakers. Cars without console by the REC: Continue with step 24. Cars where the console at the REC is fitted: Continue with step 54. Important The speakers must be fitted with the cover at the top. F930A210 21 23 23 23 23 23

15. 12 832 514 15 Saab 9-3 CV M04- Cars where the bracket at the REC is fitted 61 CD changer and/or DVD player is fitted: Fit one connection on the set's fibre optic cable in position 1 in the set's connector. Fit the lock. 62 CD changer and/or DVD player is fitted: Fit the other connection on the set's fibre optic cable in position 2 in the removed connector. Fit the lock. 63 CD changer and/or DVD player is fitted: Fit the small connector in the large connector for the CD changer or DVD player. 64 CD changer and/or DVD player is fitted: Con- nect the CD changer or DVD player connector. Proceed to step 65. F930A218 62 63 61 61

14. 14 12 832 514 Saab 9-3 CV M04- Cars where the bracket at the REC is fitted 54 Remove the bracket and take it out to facilitate access. 55 Locate the connector for the amplifier by the REC. Remove the tape and pull the connector forwards. 56 Fit the cover on the amplifier's connector. 57 CD changer or DVD player is fitted by the REC: Remove the CD changer / DVD player connector and remove the small connector from the large connector. CD changer and DVD player is fitted by the REC: Remove the CD changer connector and remove the small connector from the large connector. 58 CD changer and/or DVD player is fitted: Remove the fibre optic cable connected to posi- tion 2 in the removed connector by opening the lock in the connector and carefully lifting the hook. 59 CD changer and/or DVD player is fitted: Fit the connection on the fibre optic cable in position 2 in the set's connector. 60 CD changer and/or DVD player is fitted: Remove the protective cover from the connec- tions on the accessory set's fibre optic cable. F930A217 58 57 58 59

11. 12 832 514 11 Saab 9-3 CV M04- Cars without console by the REC 37 Locate the loose fibre optic cable and the con- nector with the fibre optic cables connected by the left-hand A-pillar (taped to the cable duct). 38 Lift up the connector lock tab. 39 Remove the fibre optic cable from the position in the connector where the arrow points outwards, to the fibre optic cable. 40 Remove the fixing tape from the loose fibre optic cable. 41 Remove the protective cover from the connection. 42 Fit the protective cover onto the removed fibre optic cable connection and carefully move the fibre optic cable aside in order to prevent dam- age, and position it behind the wiring harness. 43 Fit the connection on the new fibre optic cable in the connector and fit the lock tab. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. Important Handle the fibre optic cables with care or the sig- nal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A214 38 37 37 43

10. 10 12 832 514 Saab 9-3 CV M04- Cars without console by the REC 34 Check that the fibre optic cable cannot bend and fit the connection on the fibre optic cable in posi- tion 1 in the small connector to the amplifier. Fit the lock. 35 Fit the small connector to the large connector. 36 Connect the amplifier. Important Handle the fibre optic cables with care or the signal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A213 35 34 36

9. 12 832 514 9 Saab 9-3 CV M04- Cars without console by the REC 28 Locate the green marked fibre optic cable by the amplifier. If there is no colour marking and if there is no console by the REC: Follow the description in steps 50 and 51 in these installation instruc- tions, shine a light onto the fibre optic cable by the amplifier and note the fibre optic cables in the luggage compartment in order to identify the fibre optic cable in question. Mark using a piece of tape. 29 Remove the fibre optic cables' connector (the small connector) from the amplifier's connector. 30 Remove the fibre optic cable connected to posi- tion 1 by opening the connector locking clip and carefully lifting the hook. 31 Position the kit's fibre optic cable along the car's existing wiring harness from the amplifier to the REC. 32 Remove the protector from the connection on the kit's fibre optic cable. 33 Fit the protective cover onto the removed fibre optic cable connection and carefully move the fibre optic cable aside in order to prevent damage. Important Handle the fibre optic cables with care or the sig- nal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. F930A212 29 30 30 31 31

3. 12 832 514 3 Saab 9-3 CV M04- Bus Communication Many parts of the car's electrical system communi- cate using a bus. There are three types of bus com- munication: P-bus (Powertrain Bus), I-bus (Instru- ment Bus) and O-bus (Optical bus). The audio system communicates via the O-bus together with the navigation system, the telephone system and others. The O-bus is optical and is a ring bus. Two fibre opti- cal cables are connected to each control module on the bus, one fibre optical cable for receiving and one for sending. Messages received are converted by each control module from a fibre optic signal to elec- trical and then converted back to optical for sending. The O-bus data transfer rate is 25 Mbit/s. AMP1 is an amplifier behind the left-hand rear side trim AMP2 is an amplifier by the REC CDC is a CD changer by the REC DVD is a DVD player by the REC When fitting new equipment to be connected to the O-bus it is important that it is connected into the correct side of the existing equipment. Important It is very important that everything connected to the O-bus is connected in a specific order, see illustration, and that the ring is closed the whole time. Connection in any other way than that described in these fitting instructions may result in several of the car's systems failing to work. F930A100 1 2 CDC 1 2 DVD 1 2 AMP2 1 2 1 2 AMP2 CDC 1 2 1 2 AMP2 DVD 1 2 1 2 DVD CDC 1 2 1 2 1 2 AMP2 DVD CDC 2 1 Important Handle the fibre optic cables with care or the signal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not splice the cables. · Do not bend the cable in a radius smaller than 25 mm. · Do not expose the cable to temperatures exceeding 85°C. · Keep the cable ends free from dirt and grime. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction.

16. 16 12 832 514 Saab 9-3 CV M04- 65 Guide the connector for the amplifier through the bracket. 66 Remove the protective cover over the fibre optic cable connection on the amplifier. 67 Fit the amplifier in the bracket, a clicking sound should be heard, connect the amplifier and align the bracket. 68 Fit the bracket. Tighten the nut on the bracket's top side. Important Handle the fibre optic cables with care or the signal may be distorted. · Do not bend the cable in a radius smaller than 25 mm. · Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and causing possible communication interruptions. · The cable should not lie against any sharp edges as this may cause increased signal reduction. WARNING The visible red light is a class 1 laser. Do not look directly into the optical fibre or the control module connector at close range. A distance of less than 20 mm between your eyes and the light source may cause eye injury. F930A219 67 68 68 66 67 68 68 Important Handle the fibre optic cables with care or the signal may be distorted. · It is very important that the two leads in the connector are not confused with one another. · Do not bend the cable in a radius smaller than 25 mm. · Keep the cable ends free from dirt and grime. · The cable should not lie against any sharp edges as this may cause increased signal reduction.

Weergaven

  • 874 Totale weergaven
  • 704 Websiteweergaven
  • 170 Ingesloten weergaven

Acties

  • 0 Gedeeld op sociale media
  • 0 Vind-ik-leuks
  • 0 Vind-ik-niet-leuks
  • 0 Opmerkingen

Aantal malen gedeeld

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Insluitingen 3

  • 22 www.saabpartners.com
  • 2 52.29.207.161
  • 42 saabpartners.com